ECD L20 Скачать руководство пользователя страница 8

 

Operational Procedures 

A. Buffer Set Selection 

The Model L20 meter has two buffer sets: 7.00, 4.01, 10.01pH and 6.86, 
4.00, 9.18 pH. The meter is factory pre-set at 7.00, 4.01 and 10.01 pH. To 
change the buffer set, turn off the unit, then press and hold the “Stand” 
key while turning on the unit again.  

[Note: There is no need to repeat this procedure every time the unit is 
power up unless one decides to change the buffer settings.] 

B. pH Calibration 

The Model L20 uses 2-point or 3-point calibration. The first point must be 
6.86/7.00, and the second point can either be 4.00/4.01 or 9.18 / 10.01. 

a.  Calibration with an ATC/Temp probe in the pH-AUTOLOCK mode 

1.  Turn the unit on. Press “Clear” key for 2 seconds, all LCD elements 

will light up. The meter clears all calibration values stored in internal 
memory. 

2.  Connect the pH electrode to the BNC connector and the ATC/Temp 

probe to the ATC/Temp connector of the unit: “ATC” icon will light 
up. “pH” icon and “AUTO” icon light up. The buffer set icon will flash. 

3.  Rinse the pH and ATC/Temp probes in distilled water and immerse 

them  in  the  first  buffer  solution  (either  7.00  or  6.86).  Allow 
temperature reading to stabilize, then press and hold “Stand” key 
for 5 seconds to calibrate. The “WAIT” icon will flash until the unit 
detects a stable reading. Once the unit calibrates the first point, the 
selected buffer remains lit up while the remaining two buffers start 
to flash. The unit is ready to be sloped at the second buffer. 

[Note:  If  the  first  buffer  solution  is  7.00  or  6.86,  at  this  moment, 
press the “Mode” key. The unit will exit the calibration mode. Single 
point calibration is complete. If the first buffer solution is 4.00, 4.01, 
9.18 or 10.00, at this moment, the unit will automatically exit the 
calibration mode. Single point calibration is complete.] 

4.  Rinse the pH and ATC/Temp probe in distilled water and immerse 

them in the second buffer solution (either 4.00/4.01 or 9.18/10.01). 
Allow  temperature  reading  to  stabilize,  then  press  “Slope”  key to 
calibrate. The “WAIT” icon will flash until the unit detects a stable 

Содержание L20





















Отзывы: