CO ICATOR
U
U
U
U
U
U
GSM WIRELESS INTERCOM
With
NO RANGE LIMIT
Model: GSM18V82 / Two Channel GSM Intercom
Installation & Owners’ Manual
1.
Important!
It is a must
to read the instructions before installing and programming the unit.
2.
HOW THE INTERCOM SYSTEM WORKS
When the call button No. 1 is pressed, the system will announce:
“Please wait and your call will be answered shortly”.
Then, the unit will dial the FIRST phone number which was programmed in the memory for the number of rings
that was programmed in the system. If the call was not answered or in case the line was busy, the unit will hang up
and dial the SECOND and THIRD phone numbers which were programmed into the unit’s memory. If there was
no answer to any of the three phone calls, then the unit will announce:
“Your call was not answered, please try later
”.
When one of the calls is answered by the owner, he can talk with the visitor and open the pedestrian gate by
pressing the HASH (#) key or opening the driveway gate by pressing the STAR (*) key on his phone.
Then, the door station will announce:
“
The gate is open. Please come in
”
.
The system will hang-up the call automatically after the period of talking time it was set for.
For Button No 2 the unit will perform the same attempts of calls as described above, but it will dial the 4
th
, 5
th
and
6
th
phone numbers which were programmed into the unit’s memory.
3.
HOW THE GSM ACCESS CONTROL WORKS
The unit can be programmed with
1000 phone numbers
to become
authorized users
that are able to open the gate with
their mobile phone with no cost of a call or range limit. When an authorized user calls the SIM card of the unit, the
system will hang-up the call and trigger the relay of the unit to open the gate.
If the person that called was not one of the authorized users, it will just hang up and do nothing.
4.The SIM CARD
You would need a MINI size SIM card to be used with this unit. Insert the SIM card into your mobile phone and
make sure that you can make a call.
=> Phone the SIM card provider and cancel the Message Bank and all the other services on this SIM card
.
Note !
Make sure that you always insert or remove the SIM card only when the unit is disconnected from the Power
.
1. Insert the SIM card.
2. Connect the GSM antenna. Do not cut or shorten the antenna’s cable. Install the
antenna as high as possible
and do
not cut or solder its cable. Note!
Do not attach the antenna to any metal surface. Stick it as high as possible to any
brick wall or wooden fence. You can order a special antenna that is designed to be attached on a metal surface if
needed.
3.
The unit has two relay outputs, Relay-1 is related to the GSM access control and Relay-2 is related to the intercom
system.
Use the Relay-1 outputs (Com.1 and N.O.1) for any electric lock/latch to open the pedestrian gate and use
Relay-2 outputs (Com.2 and N.O.2) to trigger any control panel’s input, to open the driveway gate.
4. Connect 12V - 24V Dc or Ac power supply (Min 2Amp) on terminals PWN1 and PWN2 – no polarity required.
A long BEEP sound will indicate POWER connection. Wait for one minute for the system to register to the network.
If the SIM card is good and active, then the system will announce
“
The unit is connected to the network
”.
If the SIM card fails to log to the GSM network, the unit will announce:
“
The unit could not connect to the network
”.
In such a case, turn the power off, remove the SIM card and insert it to your mobile phone and check if you can make
a call.
5.
Program the system as required according to the following owner’s manual.
Important!
SEAL WITH SLICON ALL THE BACK HOLES OF THE DOOR STATION TO PROTECT THE UNIT.
