Ebyte E104-BT10-IPX Скачать руководство пользователя страница 13

Chengdu Ebyte Electronic Technology Co., Ltd

E104-BT10-IPX User Manual

Copyright ©2012–2019

C

hengdu Ebyte Electronic Technology Co., Ltd

4-12

values cannot be the same between different networks, because E104_BT10G will assign netkey to E104_BT10N and
bind APPkey when networking.

Networking process steps and results

The formation of the entire network is completely automatic. The user only needs to give the "Add Node to

Network" command on the serial port. The networking process takes up to 30 seconds, but usually it takes 10 seconds to
20 seconds to succeed.

Step 1. Start networking.

Use the serial port assistant hexadecimal to send the "device access network" command (see manual 3.1.10). The

indicator of E104_BT10G lights up. When it is lit, it means that the process of networking has started. Go to step 2.

Step 2. Scan the surrounding equipment

After our E104_BT10G receives the "Add Node to Network" command, the indicator lights up. At this time,

E104_BT10G will search for E104_BT10N devices that can be networked. The search time is 10 seconds. If it is within
10 seconds. If the networkable device is successfully scanned, go to step 3. Otherwise, the E104_BT10G indicator will
go out. The serial port will return the error code of the device that has not been scanned to the network (see manual 3.1),
and the networking process will end.

Step 3. Assign Netkey

The timeout period for assigning netkey is 10 seconds. If netkey is successfully assigned within 10 seconds, go to step 4.
Otherwise, the indicator will go out. The serial port will return the error code for assigning netkey failure (see details
from 3.1) and terminate the networking process.

Step 4. Bind Appkey

The timeout period for binding the APPkey is 10 seconds. If the APPkey is successfully bound within 10 seconds, the
serial port will return data in the following format.

The entire network can be used normally.
If the binding of appkey fails, the serial port returns the error code of binding APPkey or APPkey timeout (see

details from 3.1). When the network is finished, E104_BT10G will be restarted. If this happens, please execute manual
section 2.3.

The above two error return processing methods can be found in the 2.3

4.2.3 Networking whitelist

The whitelist function is MAC filtering. Our whitelist has a total of 8 levels of depth, that is, MAC filtering for up

to eight devices. This function is based on the fact that the eight levels of depth have an index, as long as you go to this.
The MAC is written inside, then the index is valid, then this function is enabled. We have the delete command. The user
can delete the whitelist and restore the index value to 0. Then the whitelist will not take effect. Network devices can be
grouped into the network (see 3.1.7 for details)

Length

0B

Data

head

40

Operation
code

09

MAC( 6 byte)

Element

address

two

byte

Element

quantity

03

Row

0B

40

09

EA FD CD BA FE DF

00 04

03

Содержание E104-BT10-IPX































Отзывы: