background image

1

General Information

How to Use This Manual

This manual is designed to provide detailed information necessary to service and repair the VORAD system.

The service procedures in this manual are for VORAD components only. To locate the information you need, simply 
locate the procedure in the index, turn to the page specified, and follow the procedure.

General Instructions

This manual states general procedures for retrofit installations of the EVT-300.  Each OEM installation location varies.  
Your vehicle may vary slightly from the general guidelines in this Service Manual.  Consult your OEM documentation for 
specific details.

Identification Tag Information and Model Designation

VORAD model designation (i.e. EVT-300) is stamped on the product tag. To identify the VORAD Manufacturing Part 
Number, Serial Number, and Service Part Number: Locate the Central Processing Unit and then locate the numbers as 
shown.

Eaton VORAD Collision Warning System

WARNING: READ DRIVER REFERENCE MANUAL PRIOR TO USE.

Model EVT-300, Forward Sensor Ferq. 24725 MHz

US Pantent Numbers 4,916,450; 5,181,038; 5,189,426; 5,280,288

Canadian Patent Numbers 1, 293,791 and other patents pending

1997 Eaton VORAD Technologies all rights reserved.

This device is sold under waiver of Canada and FCC Industry rules.

Any interference that may be caused should be reported to

your local FCC Feild Office or to the Federal Communications

Commission; Field Operations Bureau; 445 12th Street SW;
Room 734, Mail Stop 1500; Washington, D.C. 20554-0001.

FCC ID: I3LEVT300

"CANADA" 2035102915

EVT-300 COLLISION WARNING RADAR SYSTEM

Made in U.S.A.

UP

Central Processing Unit

40###-###

CA#####X

8####-###

Manufacturing Part Number
Serial Number
Service or OEM Part Number

Eaton VORAD Collision Warning System

WARNING: READ DRIVER REFERENCE MANUAL PRIOR TO USE.

Model EVT-300, Forward Sensor Ferq. 24725 MHz

US Pantent Numbers 4,916,450; 5,181,038; 5,189,426; 5,280,288

Canadian Patent Numbers 1, 293,791 and other patents pending

1997 Eaton VORAD Technologies all rights reserved.

This device is sold under waiver of Canada and FCC Industry rules.

Any interference that may be caused should be reported to

your local FCC Feild Office or to the Federal Communications

Commission; Field Operations Bureau; 1919 W. St. NW;

Room 734, Mail Stop 1500; Washington, D.C. 20554-0001.

Manufactured by EATON VORAD Technologies, San Diego, California

FCC ID: I3LEVT300

"CANADA" 2035102915

Eaton  

Eaton  VORAD

VORAD

R

R

Eaton  

Eaton  VORAD

VORAD

R

R

Eaton  

Eaton  VORAD

VORAD

R

R

Содержание VORAD

































Отзывы: