background image

3

Technical Data 

PR211-183-505-01

VoCALL CFVCCM9 compact master 

  

  

EATON

 www.eaton.com

Unpacking the VoCALL CFVCCS10  

compact slave unit

Remove the VoCALL Compact unit from its packing, and check 

the contents against the following list:

1.  VoCALL CFVCCS10 Compact slave unit.
2.  Installation & maintenance manual (this document).
3.  User guide & logbook.
4.  Accessory pack with the following contents:

a. Spare mains fuse.
b. 2.5 mm AF ALN key.

Using the ALN key supplied, open the front cover.

 

Verify the following items are present:

1.  10 off outstation line connectors
2.  1 off 4 way network connector

If there are any Items missing please contact your supplier or 

Cooper Safety Fire Systems, quoting the unit serial number,  

and the name on the packing list enclosed so we can rectify  

the situation.

Preparation

Remove the front door plate containing the circuit board by 

unscrewing the door hinge. This has a connection to the base 

PCB, which needs to be removed. Exercise static precautions  

to prevent damage to the electronics. Store the front panel 

assembly safely until the master handset is mounted and  

cables have been attached.

Before mounting the unit on the wall it is advisable to remove 

the cable knockouts. Decide how the wiring will be brought into 

the panel and remove the required knockouts for cable entry. If a 

knockout is removed, fill the hole with a good quality cable gland.
On the bottom face a single knockout is for the incoming mains. 

Mains SHOULD NOT enter the box by any other hole. If additional 

holes are required, then the can be drilled as shown below, taking 

care not to obscure the battery or PCB locations.
Unused knockouts must be left unopened to comply with the LVD. 

Accidentally knocked out holes should be blanked off. This work 

must be carried out prior to the re-installation of circuit boards.

Mounting VoCALL compact unit

The VoCALL Compact unit weighs 4Kgs with batteries, so care 

should be taken to securely mount the unit on stud walling.

Connecting VoCALL compact unit

To comply with EMC (Electro Magnetic Compatibility) regulations 

and to reduce the risk of electrical interference in the system 

wiring, we recommend the use of fire-resistant screened cables 

throughout the installation.
All wiring should come into the enclosure via the knockouts 

provided, and be fixed tidily to the relevant terminals.
Note that correct cable glanding is essential and due regard  

should be paid to any system specifications which demand a 

certain cable type (providing it meets the appropriate national 

wiring regulations).

Planning the wiring

All system wiring should be installed to meet the appropriate  

parts of BS5839-9 (2011) and BS 7671 (Wiring Regulations).  

Other national standards of installation should be adhered to 

where applicable.
Do not test wiring with an insulation tester (Megger) with any 

equipment or outstations connected, as the 500 Volt test voltage 

will destroy these devices totally.
You must observe local wiring regulations. Do not run SELV  

and LV cables in the same enclosure without adequate  

insulation between them.

Содержание VoCALL CFVCCM9 compact master














Отзывы: