background image

4

Safety information

EATON TFX INSTALLATION AND OPERATION MANUAL

   6046279-001   

September 2019

   www.eaton.com

2.0  Safety information

This chapter contains important information on how to avoid 

life-threatening situations and injuries and how to prevent 

product damage.

2.1  Safety instructions

!

  DANGER

Failure of safety-related functions due to deficient 

data transmission.

Severe injury or death.

The device operates using radio signals and is not 

authorized for use in safety-related applications. Insufficient 

mobile network availability, interference or malfunctions of 

the device can cause faulty data transmission. Because of 

this, data transmission can not be guaranteed at all times 

and under all conditions.

 

Never operate this device in machines or applications 

where life depends on the fault-free operation of 

this device.

 

Never rely solely on wireless devices for 

essential communications.

 

The device is designed to be used in systems which 

must be checked for conformity with the respective valid 

legal requirements prior to putting into operation. The 

integrator of the device is responsible for ensuring that 

the final system complies with all regional regulations 

and requirements.

!

  DANGER

Failure of communications systems in aircraft due to radio-

frequency energy.

Severe injury or death.

 

Disconnect the power supply to the device before 

entering the aircraft.

 

Make sure the device cannot be switched on inside 

the aircraft.

 

Note the information in chapter Power management.

!

  DANGER

Danger of explosion due to the operation of electrical 

equipment in potentially explosive atmospheres.

Severe injury or death.

 

Observe the applicable regulations and precautions for 

potentially explosive areas.

 

Do not mount the antenna in the close proximity of easily 

ignited substances (e.g. fuel tanks) and insufficiently 

shielded electronic devices.

!

   WARNING

Danger of interference with medical equipment caused 

by radio frequency (RF) energy.

Severe injury or death.

Medical equipment may be sensitive to RF energy.

The functioning of cardiac pacemakers, other implanted 

medical devices, and hearing aids can be affected if the 

TFX is located too close to the medical devices.

 

Observe the local regulations for use of mobile radio 

devices in hospitals or other medical facilities. Disconnect 

the power supply to the device when local regulations in 

sensitive areas require that you do so.

 

If you use a cardiac pacemaker or other medical device, 

do not come within the close vicinity of the switched-on 

TFX and its antenna.

 

If in doubt about potential danger, contact a physician or 

the manufacturer of the medical equipment to verify that 

it is properly shielded.

!

   WARNING

Danger to life due to electric shock!

Severe injury or death.

 

Never use the device if you suspect damage to the 

power supply unit or the device, or if there is visible 

damage to the power supply unit or the device. 

!

   WARNING

Danger to life due to electric shock!

Severe injury or death.

 

Never carry out repairs to the device yourself. Contact the 

support service. The device does not contain any parts 

that can be repaired or maintained by the user.

!

   WARNING

Overload damage due to malfunction.

Severe injury or death.

 

To limit power in the event of malfunction, secure the DC 

power supply circuit during installation with an external 2 

A fuse.

!

  CAUTION

Health hazards of radio-frequency energy

Slight or medium injury.

 

During operation, observe a distance of at least 20 cm 

between the antennas and personnel.

Содержание TFX Series





























































Отзывы: