Eaton SONIX Hmi-5 Скачать руководство пользователя страница 13

Sonix Hmi-5 Technical Manual

13

SONIX HMI-5 TECHNICAL MANUAL  

TM373 / A  June 2022  www.eaton.com

5.4.4  Important Message (Emergency Speech)

Important Message is a toggle action button. It will 

normally self-clear after ~30 seconds of no action of 

either a button press or PTT broadcast. The standard set 

up is to require a second action to broadcast Emergency 

Speech, i.e. to actively select Important Message then 

begin broadcast with PTT.

If assigned to a standard button the associated indictor 

has the following states:

Off

Important Message is not active 

Slow flashing (0.5 Hz)

An Important Message is being broadcast on the 

system

Solid

Important Message is active on the local panel 

(may or not be broadcasting)

ote: 

N

An important message broadcast is to all areas unless specified 

as part of the unit ordering.

5.4.4.1  Combined Important Message and PTT

A combined PTT and Important Message button will 

broadcast Emergency Speech while activated.

The indicator will follow the same pattern as for standard 

PTT.

Warning:

 Check regulatory requirements 

regarding Emergency Speech broadcasts as 

some require a two-step process to avoid 

accidental activation.

5.4.5  Zone button

Zone buttons can be used to give the Hmi-5 access 

panel increased speech broadcast flexibility by allowing 

the pre-selection of broadcast zones before activation of 

PTT.

Zone buttons have a timeout of ~6 seconds. If no PTT 

or additional zone button activation occurs within this 

time window, they all self-clear. Each button activation 

resets the timeout counter.

Warning:

 The default zoning of PTT and zone 

buttons must be specified as part of unit 

ordering.

If assigned to a standard button the associated indictor 

has the following states:

Off

Associated Zone(s) are not active 

Slow flashing (0.5 Hz)

Associated Zone(s) are being broadcast into by 

the system

Fast flashing (5 Hz)

Associated Zone(s) are pre-selected by the local 

panel (PTT not active)

Solid

Associated Zone(s) are selected by the local panel 

(may or not be broadcasting)

5.4.6  Alarm activation

Alarm activation buttons can be set to activate any one 

of Alarms 1 to 6. Alarms by default are all areas, but 

fixed function zoned alarms are possible (see 6.4.6.1 

Zoned alarms).

Typical associated indicator function:

Off

Associated Alarm is not active

Slow flashing (0.5 Hz)

Associated Alarm is active on the system but not 

from the local access panel

Solid

Associated Alarm is active from the local access 

panel

ote: 

N

Alarm activation function within Sonix PA/GA is NOT a toggle 

action, clearing the alarm requires activation of Alarm Cancel.

5.4.6.1  Zoned Alarms

Alarm activation function on the Sonix Hmi-5 are 

usually All-Call, i.e. activates the alarm into all areas. It 

is possible to change the default action to be a zoned 

alarm

ote: 

N

This is not recommended but if zoned alarm activation is required 

please discuss with local Eaton representative.

5.4.7  Alarm Cancel

Alarm Cancel button is provided to allow a user to clear 

or ‘cancel’ active alarms on the system. Please note 

that once pressed there is no method of un-actioning an 

Alarm Cancel.

Activating Alarm Cancel button will send a signal to 

the 2Mx requesting a clear out of any currently active 

alarms. If the activation input is still active, for example a 

remote push-button connected into the IO-Tu, then the 

alarm will immediately re-activate (although the audio 

will pause for up to a second). The alarm cancel signal 

self clears after ~ 200 milliseconds to prevent a broken 

or stuck button from acting as an un-intended alarm 

inhibit.

If assigned to a standard button the associated indictor 

has the following states:

Off

Alarm Cancel is not active 

Fast flashing (5 Hz)

Alarm Cancel is active on the system

Solid

Alarm Cancel is active locally but not on the 

system

ote: 

N

: As part of system design for un-attended access panels in pub-

lic spaces; consideration should be taken as to whether Alarm Cancel is 

a protected function.

Содержание SONIX Hmi-5























Отзывы: