Eaton SC300 Скачать руководство пользователя страница 89

Страница: 89 / 166

System Operation

IPN 997-00012-03 B2 Issue B2 July 2018

Input/Output (I/O)

The following section describes the I/O functions available with a single IOBGP I/O board.



Also see I/O Board Mapping on page 145.

Optional SiteSure-3G Input / Output (I/O) modules or additional IOBGP I/O boards can be

connected to the SC300 to provide additional I/O to monitor and control external devices. For

details refer to the SiteSure-3G Installation Guide (see Related Information on page i).

Identify an I/O Board

Input /Output (I/O) boards and SiteSure-3G modules are referenced by their serial numbers.

► To identify a particular I/O board or SiteSure-3G module

Either:

•

On SC300 keypad go to:

Settings

IOBs

and select a module or board. Press

Enter



The I/O board details screen appears. Use

to scroll to other I/O boards.

•

The Power-on LED on the selected I/O board or SiteSure-3G module will flash for 60 seconds

(or press

Esc

to stop).

Or:

•

On the web, go to:

System

> Interfaces >

RXP

RXP Devices

•

Web: click on

Start Identifying

•

The Power-on LED on the selected I/O board or SiteSure-3G module will flash for 60 seconds.

Analog System Values

The SC300 provides access to the following system analog values.

Parameter

Description

Where to find:

Bus Voltage

The average of all analog inputs configured as

Bus

Voltage

. Otherwise, the system bus voltage is

determined from the rectifier output voltages.

SC300: Analogs
DCTools:

Analog Inputs >

System Values
Web: Analog

Input / Output

> Analog Inputs

> System Values

Load Current

The sum of any analog inputs configured as

Load

Current

. Otherwise, if

Battery Current

is available, the

Load Current

is calculated as

Rectifier Current

Alternative Source Current

Battery Current

. Otherwise

it is unavailable.

Rectifier Current The sum of any analog inputs configured as

Rectifier

Current

. Otherwise, if there are

Battery

and

Load

Currents

, the

Rectifier Current

is calculated as

Battery

Current

Load Current - Alternative Source Current

Otherwise,

Rectifier Current

is determined as the sum

of all reported rectifier output currents.

Battery Current

The sum of any analog inputs configured as

Battery

Current

. Otherwise, if

Load Current

is available, the

Battery Current

is calculated as

Rectifier Current

Alternative Source Current

Load Current

. Otherwise it

is unavailable. If positive, the battery is being

charged.

Содержание SC300







































































































































































Результаты поиска

Содержание SC300

Отзывы:

Похожие инструкции для SC300

Бренды по названию

Популярные бренды

Eaton SC300, Руководство по эксплуатации

Результаты поиска

Содержание SC300

Отзывы:

Похожие инструкции для SC300

Бренды по названию

Популярные бренды