background image

13

PKE-COM-RTU Modbus RTU communication interface for PKE12/32/65 

03/20 MN034005EN

Register 

(FC04)

Description

Meaning

Note

3 0025

LOG-MAX-TH

Maximum thermal motor image 

protocol [%]

Always available

3 0026

LOG-MAX-I-REL-

MAX

Maximum value relative current value 

protocol of the

highest phase current [%], for PKE-

XTU(W)A-… only

Always available

3 0027

LOG-MAX-I-REL-L1

Protocol of maximum value relative 

phase current L1 [%], only for PKE-…

CP-…

Always available

3 0028

LOG-MAX-I-REL-L2

Protocol of maximum value relative 

phase current L2 [%], for PKE-…CP-… 

only

Always available

3 0029

LOG-MAX-I-REL-L3

Protocol of maximum value relative 

phase current L3 [%], for PKE…CP-… 

only

Always available

3 0030

LOG-PKE ON

Specifies how often the PKE has been 

switched from OFF to ON

Always available

3 0031

LOG-PKE overload

Specifies how often the PKE has 

switched off with overload

Always available

3 0032

LOG-PKE overcurrent Specifies how often the PKE has 

switched off with a short circuit

Always available

3 0033

LOG-PKE phase loss Specifies how often the PKE has 

switched off with phase failure

Always available

3 0034

LOG-PKE test trip

Specifies how often the PKE has been 

switched off with test trip

Always available

3 0035

LOG-PKE remote trip Specifies how often the PKE has been 

switched off with remote tripping

Always available

3 0036

LOG-PKE flash

Specifies how often the memory has 

been written

Always available

-

-

-

-

3 0041

R-I-REL-L1

Relative phase current L1 [raw data %], 

for PKE…CP-… only

3 0042

R-I-REL-L2

Relative phase current L2 [raw data %], 

for PKE…CP-… only

3 0043

R-I-REL-L3

Relative phase current L3 [raw data %], 

for PKE…CP-… only

 -

-

-

-

3 1024

Vendor_ID

Unique manufacturer ID

 0x01

3 1025

Device_ID

Unique device identifier

 0x22

3 1026

sw_ver

Software version

100 - 999

3 1027

hw_ver

Hardware version

100 – 999 

3 1028

stack_ver 

Modbus stack version number

0x0102 = v1.2

3 1029

build_ver

Modbus build number

0x71AA = from GIT

3 1030

App_ver

Application number

0x0102 = v1.2

3 1031

AppBuild_ver

Application build number

100-999

3 1032

ASIC2_ver

ASIC2 version number 

0xFFEF

3 1033

ASIC2_serialLW

Individual ASIC2 serial number, low 

word

3 1034

ASIC2_serialHW

Individual ASIC2 serial number, high 

word

2 Modbus RTU

2.7 Programming

Содержание PKE-COM-RTU























Отзывы: