background image

2

EATON    

 IB506017EN 

    

 Installation instructions

Installation Instructions – Tracer (Small / Large) 

Tools Required

Phillips head screw driver and electrical wiring tools. 

1-1/16 Inch (27mm) crowfoot wrench.

otee:

N

This configuration is equipped with an adjustable 

knuckle which can be mounted directly to the 1/2” 

NPS access hole in the cover plate of the junction 

box. 

1.  Loosen the knuckle center screw with phillips head 

screw driver. Adjust the position and angle of the 

knuckle stem. Re-tighten the center screw to 9 in-lbs 

for Tracer Small or 17 in-lbs for Tracer Large. (Figure 1.)

Figure 1.   

Figure 2.   

Fixture

Black

White

Green

Violet

Grey

(+) Line

Snoot Visor 

(Included)

Flat Visor 

(Installed)

(-) Common

Ground

Dim +

Dim -

2.  Route electrical leads through the 1/2” NPS access 

hole in cover plate (supplied by others). Secure knuckle 

to cover plate with lock nut. Adjust aiming angle of the 

fixture by loosening the lock nut. Re-tighten the lock nut 

to the cover plate at 48 in-lbs using a crowfoot wrench. 

(Figure 2.) 

otee:

N

Installer must apply silicone compound around entire 

perimeter of the 1/2” NPS threads where it mates to 

the mounting surface. This will create a water tight 

seal between the fixture threads and the mounting 

surface. 

3.  Make wire connection in outdoor rated junction box. 

Use wire nuts or other approved connectors to wire 

fixture per wiring diagram. (Figure 3.)

otee:

N

Mounting the cover plate to the junction box and 

then screwing the knuckle of the luminaire into the 

cover plate can result in the twisting the wires, 

causing connections to break and creating a shock 

hazard when power is turned on. 

4.  Push wires into junction box and install cover plate 

(with luminaire attached) to the junction box.

otee:

N

Ensure wires do not get pinched. 

Snoot Visor Installation

To change the visor, unscrew the phillips 4-40 screws 

holding the flat visor. Replace visor with snoot visor and 

align the arrow on the visor downwards. Insert the phillips 

4-40 screws into the visor screw holes and tighten until 

visor is secure. Tighten/torque to 8 in-lbs. (Figure 4.)

Figure 3.

Figure 4.

Содержание Lumark TCR Series








Отзывы: