manualshive.com logo in svg
background image

LCR 6600 RFN Load Control Switch (Brazil)

FCC COMPLIANCE STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna. 
• Increase the separation between the equipment and receiver. 
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

These devices operate under Part 15 of the FCC rules. Modifications to these devices not expressly authorized by Eaton’s Cooper
Power Systems may affect your ability to legally operate these devices.

DISCLAIMER OF WARRANTIES AND LIMITATION OF LIABILITY

THERE ARE NO UNDERSTANDINGS, AGREEMENTS, REPRESENTATIONS, OR WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OTHER THAN THOSE
SPECIFICALLY SET OUT BY ANY EXISTING CONTRACT BETWEEN THE SELLER AND BUYER. ANY SUCH CONTRACT
STATES THE ENTIRE OBLIGATION OF SELLER. THE CONTENTS OF THIS INFORMATION LEAFLET SHALL NOT BECOME
PART OF OR MODIFY ANY SUCH PRIOR OR EXISTING AGREEMENT.

The information, recommendations, descriptions, and safety notations are based on Eaton’s Cooper Power Systems
experience and judgment. THIS INFORMATION SHOULD NOT BE CONSIDERED AS ALL-INCLUSIVE OR COVERING ALL
CONTINGENCIES. If further information is required, Eaton’s Cooper Power Systems should be consulted. In no event will
Eaton’s Cooper Power Systems be responsible to the user in contract, in tort (including negligence), strict liability or otherwise
for any special, indirect, incidental, or consequential damage or loss whatsoever; or claims against the user by its customers
resulting from use of information, recommendations, descriptions, or safety notations.

One Cooper | www.cooperpower.com | Online

Copyright © 2013 Eaton. All rights reserved.

Eaton, Cooper Power Systems, SelectCom and Yukon are valuable

trademarks of Eaton in the U.S. and other countries. You are not

permitted to use Eaton trademarks without the prior written consent of

Eaton.

CT-Y0-0557 REV1

!

SAFETY

FOR LIFE

LCR 6600 RFN Specifications

Communications

SelectCom Radio Frequency Mesh Network

Operating Frequency:

902 to 907.5 MHz and 915 to 928 MHz
License Free Band

RF Maximum Output Power:

30 dBm (1 W)

Data Rates:

38.4 kbps, 76.8 kbps and 153.6 kbps 

Receiver Sensitivity:

-104 dBm (@ 1% PER, +25 

C, 38.4 kbps)

-101 dBm (@ 1% PER, +25 

C, 76.8 kbps)

-98 dBm (@ 1% PER, +25 

C, 153.6 kbps)

Mode:

Frequency Hopping Spread Spectrum (FHSS)

Operating Requirements

Power Source:

120/240 VAC (±20%) at 50/60 Hz
24 VAC (-20%, +10%) at 50/60 Hz

Supply Output:

12 V ±5%, 12 W

Temperature:

-40º F to 131º F (-40º C to +55º C)

Relative Humidity:

0 to 95% non-condensing

Relay Control

Low Power: 

Form C (SPDT) non-latching

Maximum Ratings:

Low Current Relays: 1 A at 28 VDC or 120 VAC
High Current Relays: 30 A at 240 VAC Resistive 

or 28 VDC

Housing

IP56 rated, injection-molded, UV-stabilized
polycarbonate plastic. Rain-tight per UL916.

Box Dimensions (Including Mounting Tabs)

10.81 in. H x 7.68 in. W x 3.60 in. D
(27.46 cm H x 19.51 cm W x 9.14 cm D)

Содержание Cooper Power System LCR 6600 RFN













Отзывы: