background image

10

Instructional Leaflet

LCR 6600 RFN Load Control Switch (Brazil)

LCR 6600 RFN Wiring Connections

Install the wiring within a 1/2 inch liquid-tight, 
non-metallic, flexible conduit or make sure the wiring 
is close nippled into an approved junction box or 
wiring compartment. All power and control wires 
must be properly terminated.

When using the enclosure’s wiring compartment, the 
divider installed within the wiring compartment must 
remain in place to isolate the low voltage wires from 
the high voltage wires. The wiring compartment is 
suitable for 1 and 2 relay configurations. Units with 3 
or more relays will require an external junction box 
for wiring termination. Please refer to 

Table 1

 and 

Table 2

 on this page for the proper wiring 

requirements.

All wiring connections are made to factory-installed, 
color-coded leads that are rated for 600 VAC, 105°C. 
The table on this page lists the color codes and 
gauges for the LCR leads.

The standard lead length is 8 inches (20.32 cm) and 
these leads are for connections within the enclosure 
wiring compartment.

Two output leads are supplied for each relay. No 
polarity requirements apply. All relay leads are 
attached via push-on connectors.

Test Button

The Test button, located on the LCR board, can 
perform the following functions:

Cancel Cold Load Pickup at Power-On

Push and hold the Test button while applying power 
to the unit to cancel cold load pickup.

Test Relay Control

Push for less than 5 seconds and release the Test 
button to control the relay for 1 minute.

The relay control initiated by the Test button is 
implemented as a standard timed load control 
command, zero delay, and zero random extension. 
This overrides any other currently implemented or 
delayed control.

NOTE: 

Pushing the Test button multiple times does 

not increment the control time by an 
additional amount of time

.

CAUTION

Incorrect connections can 

damage the LCR when power is applied. 
Follow all applicable Local and National 
Electrical Codes when wiring the LCR.

MISE EN GARDE

Un branchement incorrect 

peut endommager le LCR au moment de la 
mise sous tension. Conformez-vous à tous les 
codes de l'électricité locaux et nationaux 
pertinents pour procéder au branchement du 
LCR.

Table 1. Wire Colors and Gauge

Connection

Lead Color

Gauge

Common

Black

18

120/240 VAC

Red

18

L1 Power (24 VAC)

Red

18

L2 Power (24 VAC)

Red

18

Relay 1

Yellow

18

Relay 2

Blue

10

Relay 3 (Low Power)

Orange

18

Relay 4 (High Power)

Green

10

Table 2. Relay Configuration

Configuration

Large 

Compartment

Small 

Compartment

One Low Current 
Relay

Power

One Low Current 

Relay

One Low Current 
Relay and One 
High Current Relay

Power plus 

One High Current 

Relay

One Low Current 

Relay

Two Low Current 
Relays

Two Low Current 

Relays

Power

One High Current 
Relay

One High Current 

Relay

Power

3 or More Relays

Junction Box is Required

Содержание Cooper Power System LCR 6600 RFN













Отзывы: