Eastwood MIG 90 Скачать руководство пользователя страница 24

Страница: 24 / 24

If you have any questions about the use of this product, please contact

The Eastwood Technical Assistance Service Department: 800.343.9353 >> email: [email protected]

PDF version of this manual is available at eastwood.com

The Eastwood Company 263 Shoemaker Road, Pottstown, PA 19464, USA 800.343.9353 eastwood.com

ACCESSORIES

CONSUMABLE ITEMS

#12211

0.023” Contact Tips (5 Pack)

#12224

0.030” Contact Tips (5 Pack)

#12210

Nozzle

#20000

MIG Consumables Kit (2 Nozzles, 20 Contact Tips)

OPTIONAL ITEMS

#12238

Gas Regulator

#21483

Eastwood Large View Auto Darkening Welding Helmet - L6700

#21484

Eastwood XL View Auto Darkening Welding Helmet - XL9300

#12589/#12590

Top Grain Cowhide 4” Cuff Welding Gloves (M/L)

#12762

L/XL/XXL Welding Jacket

#20640

10’ Long Ground Cable Extension

Содержание MIG 90

























Результаты поиска

Содержание MIG 90

Отзывы:

Похожие инструкции для MIG 90

Бренды по названию

Популярные бренды

Eastwood MIG 90, Руководство по сборке и эксплуатации

Результаты поиска

Содержание MIG 90

Отзывы:

Похожие инструкции для MIG 90

Бренды по названию

Популярные бренды