Eastwood 20636 Скачать руководство пользователя страница 2

Страница: 2 / 12

Eastwood Technical Assistance: 800.544.5118 >> [email protected]

The

EASTWOOD MIG STUD WELDING KIT

transforms your MIG welder into a Stud Welder

which can be used to repair and remove dents from sheet metal.

CONTENTS

The following items should be included with your Eastwood MIG Stud Welding Kit

(1)

Stud Welding Nozzle

(1)

Slide

Hammer

(1)

2mm Hex Key

(100)

2mm Pins

SAFETY INFORMATION

DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.

WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION used with the safety alert symbol, indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.

READ INSTRUCTIONS

Read all manuals included with specific MIG welders used during the
stud welding process. Be aware of all welder safety warnings.

Содержание 20636













Результаты поиска

Содержание 20636

Отзывы:

Похожие инструкции для 20636

Бренды по названию

Популярные бренды

Eastwood 20636, Инструкция по эксплуатации

Результаты поиска

Содержание 20636

Отзывы:

Похожие инструкции для 20636

Бренды по названию

Популярные бренды