background image

14   Installation 

For units equipped with a  takeaway conveyor at  the exit of the L-sealer, provision 
should be made for exiting packages. For example, a table or bin where packages that 
have been sealed  will be placed until they can be picked  up, or a conveyor that will 
move them to the tunnel. 
 
If the L-sealer  is part of a longer packaging line, take into consideration  the table and 
conveyor height in relation to adjacent machinery. 
 
The machine should be placed on a flat, level floor so that it does not rock or move. We 
recommend that the machine be securely locked in place when used. 
 
Set up the L-sealer and move it to its location. The casters allow easy movement over 
smooth flat surfaces. If you need to lift the unit to move it, you will need to use a pallet 
jack, floor crane, or fork lift to move it to its location. 
 

CAUTION! 

If the L-sealer must be lifted for moving, use proper 
equipment when lifting and moving it to ensure it is secure 
and will not shift. 

 
When the L-sealer has been moved to its location, use the levers on the casters to lock 
the wheels  to prevent rolling and keep the unit in place.  A power cord (with optional 
electrical plug) should be installed by a licensed electrician. 
 

CAUTION! 

Before operating, ensure the following. 
1.  All shipping ties are removed. 
2.  All personnel are clear of the equipment. 
3.  Electrician has stated that all electrical work is complete. 
4.  Adjust all controls according to the settings sheet. 

 
Refer to instructions in the Operation section for instructions to power up or shut down 
the machine. 
 
 

Содержание Perfomance EN Series









































Отзывы: