7
CHARGING THE BATTERY PACK
SEE CHARGER MANUAL FOR COMPLETE INSTRUCTIONS
OPERATING
REWINDING SPOOL FROM BULK LINE
(Fig
.
9
)
(USE ONLY .065” DIAMETER LINE)
Bulk line for your trimmer is available at extra cost from your
local dealer. To install bulk line, follow these steps:
Turn off the trimmer and remove the battery.
Cut line to a length of 21.3 feet.
Press the release tabs on the line spool cover as shown
in Fig. 9, and remove the spool by pulling it straight off.
Remove and discard all line on the spool.
Insert one end of the bulk line
into the hole in the spool.
Hold the line in the hole. Snugly
and evenly wind the bulk line
onto the spool in the direction of
the arrow (clockwise) until it is
nearly full. ( Fig
10
)
Insert the line end through the
eyelet in the spool hub. Pull the
line through the eyelet to
maintain tension while placing the spool down into the
hub with the notched side exposed.
Press the spool down GENTLY and rotate it until you
feel it drop into place. (When in place, the spool will turn
a few degrees left and right freely.)
Snap the spool cover back on, insert the battery and
turn the tool on. In a few seconds you’ll hear the nylon
line being cut automatically to the proper length.
REPLACING SPOOL / CLEARING JAMS AND TANGLED
LINES
( Fig
.
9
)
From time to time, especially when cutting thick or stocky
weeds, the line feeding hub may become clogged with sap
or other material and the line will become jammed as a
result. To clear the jam, follow these steps.
●
Turn off the trimmer and remove the battery.
●
Press the 2 release tabs on the line spool retainer and
remove the cover by pulling it straight off.
●
Lift the spool of nylon line out of the hub and clear any
broken line or cutting debris from the spool area.
●
In case of jams and tangled line, unwrap about one foot
(30cm) of line to ensure that it is undamaged. If it is OK,
rewind it and insert the line ends through the eyelets in
the spool hub. Pull the line through the hole to maintain
tension while placing the spool down in to the hub with
the notched side exposed.
●
Press the spool cover down GENTLY and rotate it until
you feel it drop into place. (When in place, the spool will
freely turn a few degrees left and right.)
●
Snap the spool cover back on, insert the battery and turn
the tool on. In a few seconds or less you’ll hear the line
being cut automatically to the proper length.
Charger
Constant Green (A
)
= Power
is
ON
Constant
Green
(
A
) +
Constant
Red
(
B
)=
Battery is charging
Constant Green (A
)
+ Constant
Green
(
B
)
= Battery is fully charged
Constant Green (A
)
+ Alternately
flashing
Red
and
Green
(
B
)
=
Temperature
Abnormality
Constant Green (A
)
+ Red
indicator
light
(
B
)
flashing
=
Something is
wrong with battery
B
A
Battery Pack
Tab
Spool
Cover
Spool
Fig
9
Nylon
Line
Eyelet
BATTERY DISPOSAL
Remove the battery pack from the string trimmer. Cover the terminals with heavy duty adhesive tape. Do not attempt to destroy or disassemble battery
pack or remove any components. This product contains lithium-ion batteries which must be recycled or disposed of properly. Local, state or federal
laws may prohibit disposal of these batteries in ordinary trash.
The RBRC seal on the li-ion battery pack indicates that the costs to recycle the battery pack at the end of its useful life has already been
paid by The Great States Corporation American Lawn Mower Company. It is illegal to place spent li-ion batteries in the local municipal
solid waste or in the trash. RBRC in cooperation with The Great States Corporation American Lawn Mower Company has provided an
environmentally friendly and easy way to recycle spent li-ion batteries. Just contact your local recycling center or call 1-800-8BATTERY
for information on where to drop off the spent battery.
Tab
Fig
10
