background image

23

Summary

 

WARNING:

 

 

Never use gasoline, gasoline type lantern fuel, 

kerosene, charcoal lighter fluid or other similar liquids to start 

or “freshen up” the fire in this fireplace or in any fireplace.

WARNING:

 

 

If processed solid fuel firelogs are used: Do not poke 

or stir the logs while they are burning. Use only firelogs that 

have been evaluated for the application in fireplace and refer 

to firelog warnings and caution markings on packaging prior to 

use.

5. Avoid over-firing this fireplace. Some examples of over-

firing are:

a. Burning of scrap lumber, construction debris, pine branches 

and brush or cardboard boxes;

b. Burning small diameter twigs, branches or any other small 

sized  combustible  materials  in  quantities  which  exceed  the 

volume of the normal log fire;

c. Use of artificial wax base logs, trash or other chemicals or 

chemically treated combustibles.

WARNING:

      Over-firing  can  permanently  damage  this 

fireplace system.

6. Fireplace Doors and Screens:

 

This fireplace has not been tested for use with doors. 

To reduce the risk of fire or injury, do not install doors. If doors 

are required by the local authority having jurisdiction then 

doors must be kept in the fully open position when the fireplace 

is  in  operation.  Isokern  does  not  limit  the  use  of  fireplace 

screens. 

7.

 

Disposal of Ashes:

 

It  is  recommended  that  the  firebox  be  cleaned  of 

excessive ashes before each use. It is necessary to remove 

ashes from the open front of the fireplace. To do so, proceed in 

the following manner:

 

Allow the fire to go out and the ashes to cool for at 

least six to eight hours.

 

After the cooling period carefully pick up the ashes

from the firebox with a small, metal fireplace shovel or other 

metal scoop and place them in a metal container with a tight 

fitting lid.

 

If possible do not sweep the ashes as this will stir 

them into the air and disperse them into the room.

 

The closed container of ashes should be placed on 

a noncombustible floor or on the ground, well away from all 

combustible materials, pending final disposal. If the ashes are 

disposed of by burial in soil or otherwise locally dispersed, 

they should be retained in the closed container until all cinders 

have thoroughly cooled.

8. Inspection and Cleaning:

 

At least twice a year in warm climates or monthly 

during the heating season in colder climates, thoroughly 

inspect the Fire-Lite fireplace and chimney system. 

Chimneys must be installed so that access is provided for 

inspection and cleaning. The chimney should be inspected 

monthly during the heating season.

 

Inspect  the  entire  flue  from  the  top  down  for 

obstructions such as birds’ nests, leaves, etc. Such obstructions 

must be removed.

 

Check spark arrestor screens for clear flow of smoke 

every two to four weeks during the heating season.

 

Inspect the flue periodically during the heating season 

for the presence of soot and creosote build up. If creosote or 

soot has accumulated, it should be removed to reduce the risk 

of chimney fire.

 

Have your chimney cleaned by a professional chimney 

sweep if you have doubts about your ability to do it.

 

Use a plastic, wood or steel brush to clean the chimney.

 

Scrub  the  spark  arrestor/chimney  cap  with  a  wire 

brush.

 

Remove any chimney cap for flue cleaning from the 

top. Open the damper in the firebox for cleaning access from 

below.

 

Clean the inner portion of the flue by using a flexible 

handled chimney cleaning brush.

 

For straight run flue the proper size brush can be pulled 

up through the flue from the firebox with the damper open.

 

If the chimney has an offset chimney section, brush

cleaning from the chimney top down to the offset/return and 

then  from  the  firebox  up  to  the  offset  section  is  the  proper 

method.

 

In either case, cover the fireplace opening with a damp 

sheet (sealed to the opening with masking tape) before brush 

cleaning. Do not remove sheet until the soot has settled. It is 

advised to vacuum loosened soot. Do not sweep loosened soot 

as sweeping will disperse soot into the air and about the room.

WARNING:

      Do  not  use  chemical  fireplace  and  chimney 

cleaners that are poured on a hot fire. These can be dangerous 

and  generally  work  only  on  the  flue  section  nearest  the  fire, 

leaving the rest of the flue unaffected.

9. Exterior Maintenance:

 

Annually, at a minimum, check all metal flashings and 

weather seals around the exterior chimney where it penetrates 

the roof surface; inspect any chimney top spark arrestors, metal 

cowlings and weather hoods to make sure they are secure and 

weather tight.

 

Seal any cracks or gaps in chimney-to-roof flashings 

to prevent possible roof and chimney chase leaks.

Inspect any cement chimney cap or clay chimney pot 

terminations to make sure they are not diverting water into the 

structure. Seal any suspected cracks or gaps in these masonry 

components.

Содержание Isokern Magnum 86072 Series


























Отзывы: