Eagle Power II Скачать руководство пользователя

Страница: 19 / 19

EAGLE-II Swing Gate Operator

____________________

Eagle Access Control Systems, Inc. / (800) 708-8848 / www.eagleoperators.com

(19)

Troubleshooting

SYMPTOMS

PROBABLE CAUSES

REMEDY

Gate stops and reverses

direction in mid travel and the

OVERLOAD LED remains ON.

(A) Gate operator is not plumb

and level.

(B) ERD current sensor may be

set to sensitive.

obstruction while in travel.

(A) Remount operator or swing

arm

(B) Turn the ERD sensor slightly

in the clockwise direction.

obstructions.

Gate will not CLOSE.

(A) The Radio Receiver's LED

remains on.

(B) One or more of the global

input LED(S) remain active.

it encountered an obstruction

while closing.

(D) The Loop Detector LED

is on.

(E) Switch #8 is not

functioning.

(A) Remote or receiver has

malfunctioned in the "on"

position.

(B) Check any Global Inputs for

a possible short circuit.

receiver will resume normal

operation.

(D) Reset Loop Detector, verify

correct wiring, set to a differ-

ent frequency and/or change

the sensitivity of the Loop

Detector.

(E) Be sure that the "Close Timer"

(switch #4) is set to the

"on" position.

Gate will not OPEN.

(A) Motor overload.

(B) Radio Receiver is not "on"

when the remote control is

activated.

(D) Fuse blown.

(A) Reset thermal breaker on

motor. (See page 18)

(B) The receiver in the gate

operator has malfunctioned

in the "off" position.

and/or reset the main circuit

breaker.

(D) Check and/or replace with

a proper fuse.

COMMON OVERSIGHTS TO BE AWARE OF:

(A) Switch #1 must be set to the "Master On" position, unless the operator is being used as a

"Slave unit.

(B) Safety Loop Detectors must be connected to the Reverse Loop input.

(D) It is Ok to call the Eagle Access Customer Service Department with any questions...we are here to

serve YOU!

1-800-708-8848

Содержание Power II




















Результаты поиска

Содержание Power II

Отзывы:

Похожие инструкции для Power II

Бренды по названию

Популярные бренды

Eagle Power II, Руководство по установке

Результаты поиска

Содержание Power II

Отзывы:

Похожие инструкции для Power II

Бренды по названию

Популярные бренды