background image

4810 Clover Road • Greensboro, NC 27450 • 1-800-336-2776 • www.eagleequip.com • © Eagle Equipment 2018.01  • page 3

PLEASE READ THE ENTIRE MANUAL BEFORE ANY 

INSTALLATION AND OPERATION OF EQUIPMENT. 

TERMS AND CONDITIONS     

Please read the safety procedures and operation instructions in this manual before operating the 
lift. Proper installation and use is very important. Keep this operation manual near the machine at 
all times. Make sure ALL USERS read and fully understand this manual. The lift should be used on a 
relatively level floor.

This is a vehicle lift setup and operation manual and no attempt is made or implied herein to instruct 
the user in lifting methods particular to an individual application. Rather, the contents of this manual 
are intended as a basis for operation and maintenance of the unit as it is intended to be used.
Proper use of this lift is included in this manual. Any other proposed application of this equipment 
should be documented and submitted in writing to Eagle Equipment for review. The user assumes full 
responsibility for any equipment damage, personal injury, or alteration of the equipment described in 
this manual or any subsequent damages.

OUR TERMS AND CONDITIONS     

Please read these terms of service carefully. 
These terms and conditions of sale (“Agreement”) are applicable to any order placed by you (the
“Customer”) with and accepted by Eagle Equipment (referred to herein as “Eagle”).

Risk of Loss / Freight / Shipping

All shipments are FOB the Eagle warehouse, which means that  ownerships of these goods transfers to 
the customer when they leave our dock
. We use common carriers that have a demonstrated history of 
timely deliveries and competitive freight rates for the benefit of our customer. Most of these carriers 
have restrictions on delivering to residential addresses and may require pick-up at freight terminal.
There are additional fees for residential, limited access and remote delivery. There are additional fees 
for lift gate services and scheduled deliveries from the freight carriers.

Delivery, Unloading and Freight Damage

Unloading: The customer is responsible for unloading the shipment from the carrier’s truck. This may 
require a forklift and/or lift gate service. Please note that Lifts will require a forklift to unload and they 
cannot be unloaded using a lift gate vehicle. The customer care team can advise you prior to shipping 
what will be needed to unload your shipment and the approximate weight of the shipment.

Damages: Any charges or damages that may be incurred as a result of unloading from the carrier’s 
truck is the customer’s responsibility.

Upon delivery, it is very important that you inspect all of your products immediately. While we make 
every attempt to prevent freight damage by properly packaging your order, sometimes damage occurs 
in transit. For your protection, it is imperative that you note any and all damage you observe on the

Содержание ETC-2800A









































Отзывы:

Похожие инструкции для ETC-2800A