background image

17

8  Cyclical I/O data

Depending on the planned module type and the selected 
sub-modules, a varying number of data bytes are exchanged in 
the cyclical data traffic.

The system allows individual determination per slot if I/O data 
(status/control), measuring values and/or total current shall be 
transmitted. The GSDML file made available for the projecting 
tool allows the related configuration the system recognises all 

permitted configurations and processes the cyclical data defined 
in the projection. 

Only the module I/O data CPC20 controller is firmly pre-set and 
cannot be removed because the input bytes hold vital failure and 
diagnostic information as described in the following.

byte

type

range

description

status controller

0 HighByte
1 LowByte

Word

0xFFFF

Bit 0 = no configuration data available
Bit1 = invalid configuration data
bit 2 = reserve
bit 3 = reserve
Bit4 = command buffer overflow
bit 5 = reserve
bit 6 = reserve
Bit7 = no communication with at least one PWR board
Bit8 = reserve
Bit9 = CPC temporary error
Bit10 = CPC hardware error
Bit11 = reserve
Bit12 = reserve
Bit13 = reserve
Bit14 = reserve
Bit15 = reserve

fig. 16: Diagnostic data

8.2  Submodule Status/Control

Depending on the number of 18plus-AM03 connection modules 
used (one 18plus-AM03 module corresponds to two channels), 
per channel one byte input data with the status of the circuit 
protector and one byte output data for control of the circuit 
protector are exchanged here. 

Example:
8 18plus-AM03 connection modules equal 16 channels. This 
results in 16 bytes for status information and 16 bytes for control 
for the data exchange.
Addressing is effected according to the 
18plus-AM03 sequence
18plus-AM03 1, channel 1.1 byte address [0]
18plus-AM03 1, channel 1.2 byte address [1]
18plus-AM03 2, channel 2.1 byte address [2]
…….

8.1  Module I/O data CPC20 controller

The 2 bytes input data contain the following global error and 
diagnostic messages. This module does not contain any output 
data.

Содержание ControlPlex CPC20

































Отзывы: