Morpheus Operation Manual
120
PRESET MENU
The function generator can be programmed to jump between segments
based on certain conditions. Because the decision to jump is based on
conditions, these jumps are called
Conditional Jumps
. For example, the
function generator could be programmed to loop only if the key is still
being held. In the diagram below, the function generator has been
programmed to jump back to segment 3 if the key is held but jump to
segment 4 whenever the key is released.
1
2
3
4
If
Note Off
Jump to 4 at
End
of Segment
5
6
7
8
If
Note Off
Immediate
ly Jump to 4
If
Note On
Immediate
ly Jump to 3
Conditional jumps can be programmed to jump to the destination
segment immediately or they can wait until the end of the segment
before jumping. The conditional jumps are:
Never
.......................... Never jumps. Always goes on to next segment.
Always End
.............. Always jumps at the end of the current segment.
Note On End
............. Jumps at the end of the segment if the note is still
on.
Note On Immed.
...... Jumps immediately if the note is still on.
Note Off End
............ Jumps at the end of the segment if the note is off.
Note Off Immed.
..... Jumps immediately if the note is off.
LFO 1 or 2 End
......... Jumps at the end of the segment if the value of the
selected LFO is equal or greater than the
conditional value.
Footsw. 1-3 End
....... Jumps at the end of the segment if the selected
footswitch is pressed.
Footsw. 1-3 Immed.
Jumps immediately if the selected footswitch is
pressed.
Velocity End
............ Jumps at the end of the segment if the velocity
value is greater than a positive conditional value
or less than a negative conditional value. See the
following page.
Key End
..................... Jumps at the end of the segment if the note value
is greater than a positive conditional value or less
than a negative conditional value. See the
following page.
▼
Remember to turn up the
LFO amount when using
LFOs as conditionals.
••• A Conditional Jump
always goes to the
Begin-
ning
of the destination
segment.
Содержание MORPHEUS
