background image

5

E-flite Ultimate 20-300 Assembly Manual

Warranty Information

Warranty Period

Horizon Hobby, Inc., (Horizon) warranties that the Products purchased 

(the “Product”) will be free from defects in materials and workmanship 

at the date of purchase by the Purchaser.

Limited Warranty

(a) This warranty is limited to the original Purchaser ("Purchaser") and 

is not transferable. REPAIR OR REPLACEMENT AS PROVIDED UNDER 

THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. 

This warranty covers only those Products purchased from an 

authorized Horizon dealer. Third party transactions are not covered 

by this warranty. Proof of purchase is required for warranty claims. 

Further, Horizon reserves the right to change or modify this warranty 

without notice and disclaims all other warranties, express or implied.
(b) Limitations- HORIZON MAKES NO WARRANTY OR 

REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-

INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A 

PARTICULAR PURPOSE OF THE PRODUCT. THE PURCHASER 

ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT 

THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE 

PURCHASER’S INTENDED USE.
(c) Purchaser Remedy- Horizon's sole obligation hereunder  

shall be that Horizon will, at its option, (i) repair or (ii) replace, any 

Product determined by Horizon to be defective. In the event of a 

defect, these are the Purchaser's exclusive remedies. Horizon reserves 

the right to inspect any and all equipment involved in a warranty 

claim. Repair or replacement decisions are at the sole discretion of 

Horizon. This warranty does not cover cosmetic damage or damage 

due to acts of God, accident, misuse, abuse, negligence, commercial 

use, or modification of or to any part of the Product. This warranty 

does not cover damage due to improper installation, operation, 

maintenance, or attempted repair by anyone other than Horizon. 

Return of any goods by Purchaser must be approved in writing by 

Horizon before shipment.

Damage Limits

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT OR 

CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION 

OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE 

PRODUCT, WHETHER SUCH CLAIM IS BASED IN CONTRACT, 

WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. Further, in no 

event shall the liability of Horizon exceed the individual price of the 

Product on which liability is asserted. As Horizon has no control over 

use, setup, final assembly, modification or misuse, no liability shall be 

assumed nor accepted for any resulting damage or injury. By the act 

of use, setup or assembly, the user accepts all resulting liability.
If you as the Purchaser or user are not prepared to accept the liability 

associated with the use of this Product, you are advised to return this 

Product immediately in new and unused condition to the place of 

purchase.
Law: These Terms are governed by Illinois law (without regard to 

conflict of law principals).

Safety Precautions

This is a sophisticated hobby Product and not a toy. It must be 

operated with caution and common sense and requires some basic 

mechanical ability. Failure to operate this Product in a safe and 

responsible manner could result in injury or damage to the Product or 

other property. This Product is not intended for use by children without 

direct adult supervision. The Product manual contains instructions for 

safety, operation and maintenance. It is essential to read and follow 

all the instructions and warnings in the manual, prior to assembly, 

setup or use, in order to operate correctly and avoid damage or 

injury.

Содержание Ultimate 20-300 10 ARF









































Отзывы: