E-FLITE thunderbolt p-47 Скачать руководство пользователя страница 8

Страница: 8 / 48

Before Starting Assembly

Before beginning the assembly of your P-47D Thunderbolt,

remove each part from its bag for inspection. Closely inspect

the fuselage, hatch, wing and stabilizer for damage. If you

ﬁnd any damaged or missing parts, contact the place of

purchase.

Note on Lithium Polymer Batteries

Lithium Polymer batteries are signiﬁcantly

more volatile than alkaline or Ni-Cd/

Ni-MH batteries used in RC applications.

All manufacturer’s instructions and warnings

must be followed closely. Mishandling of Li-Po

batteries can result in ﬁre. Always follow the

manufacturer's instructions when disposing of

Lithium Polymer batteries.

Using the Manual

This manual is divided into sections to help make assembly

easier to understand, and to provide breaks between each

major section.

Remember to take your time and follow the directions.

Warning

An RC aircraft is not a toy! If misused, it can cause serious

bodily harm and damage to property. Fly only in open

areas, preferably at AMA (Academy of Model Aeronautics)

approved ﬂying sites, following all instructions included with

your radio.

Keep loose items that can get entangled in the propeller

away from the prop, included loose clothing, or other objects

such as pencils and screwdrivers. Especially keep your hands

away from the propeller.

Содержание thunderbolt p-47

















































Результаты поиска

Содержание thunderbolt p-47

Отзывы:

Похожие инструкции для thunderbolt p-47

Бренды по названию

Популярные бренды

E-FLITE thunderbolt p-47, Инструкция по сборке

Результаты поиска

Содержание thunderbolt p-47

Отзывы:

Похожие инструкции для thunderbolt p-47

Бренды по названию

Популярные бренды