E-FLITE thunderbolt p-47 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 48

background image

Wing Installation

Required Parts

• Wing

• Fuselage

• Belly pan

Required Tools and Adhesives

• Phillips screwdriver



1. Place the wing onto the fuselage. Make sure to

pass the Y-Harness lead through the opening in
the fuselage.



2. Place the belly pan onto the wing and fuselage.

The mounting plate at the rear of the belly pan
keys into the fuselage mounting plate. Use the
screw at the front to secure the belly pan and
wing to the fuselage.

14

«
...
12
13
14
15
16
...
»

Содержание thunderbolt p-47

















































Отзывы:

Нет отзывов

Похожие инструкции для thunderbolt p-47

Traffic Light-Grand

Бренд: Jamara Страницы: 4

Mercedes-Benz Arocs

Бренд: Jamara Страницы: 4

Mercedes-AMG GT

Бренд: Jamara Страницы: 8

Liebherr 2,4 GHz

Бренд: Jamara Страницы: 8

Бренд: Jamara Страницы: 20

Beaver DHC 2 V2

Бренд: Jamara Страницы: 24

Бренд: Jamara Страницы: 16

Бренд: Jamara Страницы: 8

Schlossberg Inn

Бренд: Faller Страницы: 12

COMET SENIOR DART

Бренд: Paul Bradley Страницы: 6

Бренд: Fisher-Price Страницы: 2

IMAGINEXT B9774

Бренд: Fisher-Price Страницы: 6

Бренд: marklin Страницы: 32

Бренд: K'Nex Страницы: 36

Lightning Flash Roller Coaster

Бренд: K'Nex Страницы: 23

Бренд: Tekno Страницы: 28

Бренд: TAMS Страницы: 17

Бренд: VBC Racing Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды