background image

27

E-flite Leader 480 ARF Assembly Manual

Warranty Services

QUESTIONS, ASSISTANCE, AND REpAIRS

Your local hobby store and/or place of purchase 

cannot provide warranty support or repair. Once 

assembly, setup or use of the Product has been started, 

you must contact Horizon directly. This will enable 

Horizon to better answer your questions and service 

you in the event that you may need any assistance. 

For questions or assistance, please direct your 

email to [email protected], or call 

877.504.0233 toll free to speak to a Product Support 

representative. You may also find information on our 

website at www.horizonhobby.com.

INSpECTION OR REpAIRS

If this Product needs to be inspected or repaired, 

please use the Horizon Online Repair Request 

submission process found on our website or call 

Horizon to obtain a Return Merchandise Authorization 

(RMA) number. Pack the Product securely using a 

shipping carton. Please note that original boxes may 

be included, but are not designed to withstand the 

rigors of shipping without additional protection. Ship 

via a carrier that provides tracking and insurance for 

lost or damaged parcels, as Horizon is not responsible 

for merchandise until it arrives and is accepted at 

our facility. An Online Repair Request is available at 

www.horizonhobby.com http://www.horizonhobby.

com under the Repairs tab. If you do not have internet 

access, please contact Horizon Product Support to 

obtain a RMA number along with instructions for 

submitting your product for repair. When calling 

Horizon, you will be asked to provide your complete 

name, street address, email address and phone 

number where you can be reached during business 

hours. When sending product into Horizon, please 

include your RMA number, a list of the included items, 

and a brief summary of the problem. A copy of your 

original sales receipt must be included for warranty 

consideration. Be sure your name, address, and 

RMA number are clearly written on the outside of the 

shipping carton.

Notice: Do not ship batteries to horizon. If 

you have any issue with a battery, please 

contact the appropriate horizon product 

Support office.

WARRANTy INSpECTION AND REpAIRS

To receive warranty service, you must include your 

original sales receipt

 verifying the proof-of-purchase 

date. Provided warranty conditions have been met, 

your Product will be repaired or replaced free of 

charge. Repair or replacement decisions are at the sole 

discretion of Horizon.

NON-WARRANTy REpAIRS

Should your repair not be covered by warranty 

the repair will be completed and payment will 

be required without notification or estimate of 

the expense unless the expense exceeds 50% of 

the retail purchase cost.

 By submitting the item for 

repair you are agreeing to payment of the repair 

without notification. Repair estimates are available 

upon request. You must include this request with your 

repair. Non-warranty repair estimates will be billed a 

minimum of ½ hour of labor. In addition you will be 

billed for return freight. Horizon accepts money orders 

and cashiers checks, as well as Visa, MasterCard, 

American Express, and Discover cards. By submitting 

any item to Horizon for inspection or repair, you are 

agreeing to Horizon’s Terms and Conditions found on 

our website under the Repairs tab.

UNITED STATES

(Electronics and engines)

Horizon Service Center

4105 Fieldstone Rd

Champaign, Illinois

61822 USA

877-504-0233

Online Repair Request visit:

www.horizonhobby.com/repairs

(All other products)

Horizon Product Support

4105 Fieldstone Rd

Champaign, Illinois

61822 USA

[email protected]

877-504-0233

UNITED KINGDOM

Horizon Hobby Limited

Units 1-4 Ployters Rd

Staple Tye

Harlow, Essex

CM18 7NS

United Kingdom

[email protected]

+44 (0) 1279 641 097

GERMANy

Horizon Technischer Service

Hamburger Str. 10

25335 Elmshorn

Germany

[email protected]

+49 4121 46199 66

FRANCE

Horizon Hobby SAS

14 Rue Gustave Eiffel

Zone d’Activité du Réveil Matin

91230 Montgeron

[email protected] 

+33 (0) 1 60 47 44 70

Compliance Information for the 

European Union

  

INSTRUCTIONS FOR DISpOSAL OF WEEE By 

USERS IN ThE EUROpEAN UNION

This product must not be disposed of with other waste. 

Instead, it is the user’s responsibility to dispose of their 

waste equipment by handing it over to a designated 

collection point for the recycling of waste electrical 

and electronic equipment. The separate collection 

and recycling of your waste equipment at the time 

of disposal will help to conserve natural resources 

and ensure that it is recycled in a manner that 

protects human health and the environment. For more 

information about where you can drop off your waste 

equipment for recycling, please contact your local city 

office, your household waste disposal service or where 

you purchased the product.

Содержание Leader 480 ARF

































Отзывы: