E-FLITE J-3 Cub 25 ARF Скачать руководство пользователя страница 2

Страница: 2 / 52

Introduction

The Piper J-3 Cub is an all-time favorite among aviation

enthusiasts everywhere. Classic lines and predictable flight

performance are just a few of the Cub’s trademarks. The

25-size J-3 Cub from E-flite

™

is the first of its size for

E-flite. The name Piper J-3 Cub .25 ARF implies the power

of a .25 glow engine, but it is designed specifically for

electric operation. This aircraft has been designed from

the start for the E-flite Power 25 Outrunner BL motor.

It uses balsa and plywood construction and is covered

with genuine UltraCote

. Using a scale of approximately

1/7, the J-3 Cub spans 62 inches delivering excellent

presentation and performance to budget-minded pilots.

You can fly with either a 10-cell Ni-MH battery, or a

3-cell Li-Po for increased performance and duration. An

optional set of scale fiberglass floats is also available

(EFLA500). All it takes is five minutes to change from

landing gear to floats to enjoy those afternoons on the

lake. Change back to the standard landing gear and you

can be shooting touch-and-go’s at the local flying field, the

choice is yours. Either way we believe you will fall in love

with the relaxing flight performance of the E-flite J-3 Cub.

Table of Contents

Introduction.................................................................2

Contents.of.Kit/Parts.Layout..........................................3

Specifications..............................................................3

Covering.Colors..........................................................3

Required.Electronics.&.Accessories................................4

Outrunner.(Direct.Drive).Motor.Setup.............................4

Required.Tools.and.Adhesives.......................................4

Optional.Accessories...................................................5

Warning.....................................................................5

Before.Starting.Assembly..............................................5

Note.on.Lithium.Polymer.Batteries..................................5

Using.the.Manual........................................................5

Limited.Warranty.Period...............................................5

Landing.Gear.Installation..............................................8

Motor.and.Cowling.Installation...................................12

Radio.Installation.......................................................16

Wing.Assembly.........................................................18

Tail.Installation...........................................................30

Linkage.Installation.....................................................34

Final.Assembly..........................................................44

Center.of.Gravity./.Battery.Installation.........................47

Control.Throws..........................................................48

Flying.Notes..............................................................49

2006.Official.AMA..

.........National.Model.Aircraft.Safety.Code.................50

Содержание J-3 Cub 25 ARF





















































Результаты поиска

Содержание J-3 Cub 25 ARF

Отзывы:

Похожие инструкции для J-3 Cub 25 ARF

Бренды по названию

Популярные бренды

E-FLITE J-3 Cub 25 ARF, Инструкция по сборке

Результаты поиска

Содержание J-3 Cub 25 ARF

Отзывы:

Похожие инструкции для J-3 Cub 25 ARF

Бренды по названию

Популярные бренды