background image

41

E-flite F-86 Sabre 15 DF ARF Assembly Manual

United Kingdom:

Electronics and engines requiring inspection or repair 

should be shipped to the following address:

Horizon Hobby UK

Units 1-4 Ployters Rd

Staple Tye

Harlow, Essex

CM18 7NS

United Kingdom

Please call +44 (0) 1279 641 097 or e-mail us at 

[email protected] with any questions or 

concerns regarding this product or warranty.

germany:

Electronics and engines requiring inspection or repair 

should be shipped to the following address:

Horizon Technischer Service

Hamburger Strasse 10

25335 Elmshorn

Germany

Please call +49 4121 46199 66 or e-mail us at 

[email protected] with any questions or 

concerns regarding this product or warranty.

France:

Horizon Hobby SAS

14 Rue Gustave Eiffel

Zone d’Activité du

Réveil Matin

91230 Montgeron

Please call +33 (0) 1 60 47 44 70 with any questions 

or concerns regarding this product or warranty.

Compliance Information for the 

European Union

INSTRUCTIONS FOR DISPOSAL OF WEEE By USERS IN 

ThE EUROPEAN UNION

This product must not be disposed of with other waste. 

Instead, it is the user’s responsibility to dispose of their 

waste equipment by handing it over to a designated 

collection point for the recycling of waste electrical 

and electronic equipment. The separate collection 

and recycling of your waste equipment at the time 

of disposal will help to conserve natural resources 

and ensure that it is recycled in a manner that 

protects human health and the environment. For more 

information about where you can drop off your waste 

equipment for recycling, please contact your local city 

office, your household waste disposal service or where 

you purchased the product.

Age Recommendation: 14 years or over. Not a toy. 

Not intended for use by children without direct adult 

supervision.

2010 Official Academy of Model 

Aeronautics Safety Code

gENERAL

 1.  A model aircraft shall be defined as a non-human-

carrying device capable of sustained flight in 

the atmosphere. It shall not exceed limitations 

established in this code and is intended to be used 

exclusively for recreational or competition activity.

 2.  The maximum takeoff weight of a model aircraft, 

including fuel, is 55 pounds, except for those flown 

under the AMA Experimental Aircraft Rules.

 3.  I will abide by this Safety Code and all rules 

established for the flying site I use. I will not 

willfully fly my model aircraft in a reckless and/or 

dangerous manner.

 4.  I will not fly my model aircraft in sanctioned events, 

air shows, or model demonstrations until it has 

been proven airworthy.

 5.  I will not fly my model aircraft higher than 

approximately 400 feet above ground level, when 

within three (3) miles of an airport without notifying 

the airport operator. I will yield the right-of-way 

and avoid flying in the proximity of full-scale 

aircraft, utilizing a spotter when appropriate.

 6.  I will not fly my model aircraft unless it is identified 

with my name and address, or AMA number, 

inside or affixed to the outside of the model 

aircraft. This does not apply to model aircraft flown 

indoors.

 7.  I will not operate model aircraft with metal-blade 

propellers or with gaseous boosts (other than 

air), nor will I operate model aircraft with fuels 

containing tetranitromethane or hydrazine.

Содержание F86 Sabre 15DF













































Отзывы: