E-FLITE F86 Sabre 15DF Скачать руководство пользователя страница 2

2

E-flite F-86 Sabre 15 DF ARF Assembly Manual

Contents of Kit/Parts Layout

Replacement Parts

EFL8101 

 Fuselage with Upper and  

Lower Hatch

EFL8102 

Canopy Hatch

EFL8103 

 Left Wing Panel with  

Hinged Aileron

EFL8104 

 Right Wing Panel with  

Hinged Aileron

EFL8105 

 Horizontal Stabilizer with 

Elevator (left and right)

EFL8106 

 Pushrods and Carbon  

Wing Tubes

EFL8107 

Plastic Accessories

EFL8108 

 Landing Gear and Wheels  

with Hardware

EFL8109 

Control Hardware

EFL8110 

Intake and Thrust Tube

EFL8111 

Consumer Decal Sheet

Introduction

This performance model was designed around E-flite’s 

Delta-V 15 (69mm) fan unit and matched 15 DF 

3200Kv brushless motor. Pilots can use a 4-cell Li-Po 

battery pack for great performance. The built-in fan 

mounts make installing the fan easy—just drop in 

the fan unit and tighten four screws. The removable 

magnetic front hatch also allows easy access to the 

radio equipment and battery. The entire trim scheme 

is prepainted, pre-trimmed; the wings are covered in 

UltraCote

®

. Just add your favorite nose art decals and 

enjoy.

Important Information  

Regarding Warranty Information

Please read our Warranty and Liability Limitations 

section on Page 39 before building this product. If you 

as the Purchaser or user are not prepared to accept the 

liability associated with the use of this Product, you are 

advised to return this Product immediately in new and 

unused condition to the place of purchase.

Using the Manual

This manual is divided into sections to help make 

assembly easier to understand, and to provide breaks 

between each major section. In addition, check boxes 

have been placed next to each step to keep track 

of its completion. Steps with a single circle (

) are 

performed once, while steps with two circles (

 

indicate the step will require repeating, such as for a 

right or left wing panel, two servos, etc.

Remember to take your time and follow the directions.

Table of Contents

Introduction ........................................................... 2

Important Information Regarding  

Warranty Information ........................................ 2

Using the Manual ................................................... 2

Contents of Kit/Parts Layout .................................... 2

Recommended Radio Equipment ............................. 3

Required Brushless Ducted Fan Setup ....................... 3

Required Tools and Adhesives ................................. 3

Optional Accessories .............................................. 3

Warnings .............................................................. 3

Aileron Servo Installation ........................................ 4

Aileron Linkage Installation ..................................... 6

Mounting the Main Wing Panels ............................. 9

Stabilizer Installation ............................................ 12

Elevator Installation .............................................. 15

Rudder Installation ............................................... 16

Elevator Servo and Linkage Installation .................. 18

Rudder Servo and Linkage Installation ................... 22

Landing Gear Installation ...................................... 24

Steering Servo and Linkage Installation .................. 26

Speed Control and Receiver Installation ................. 27

Intake Tube Installation.......................................... 29

Fan Installation..................................................... 30

Exhaust Tube Installation ....................................... 32

Securing the Intake Tube ....................................... 34

Canopy Assembly ................................................ 35

Motor Battery Installation ...................................... 35

Decal Placement ................................................... 36

Center of Gravity ................................................. 36

Control Throws..................................................... 37

Preflight ............................................................... 38

Flying Your F-86 Sabre 15 DF............................... 38

Range Test Your Radio .......................................... 38

Safety Do’s and Don’ts for Pilots ............................ 39

Daily Flight Checks ............................................... 39

Warranty and Repair Policy .................................. 39

Warranty Services ................................................ 40

Compliance Information for the European Union .... 41

2010 Official Academy of  

Model Aeronautics Safety Code ....................... 41

Содержание F86 Sabre 15DF













































Отзывы: