E-FLITE Aeronca Champ 15E ARF Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 36

background image

19

E-flite Aeronca Champ 15e ARF Assembly Manual



7. Locate the standard servo horn included with your

servo. Use a pin vise and 5/64-inch (2mm) drill bit

to enlarge the hole in the servo arm that is 3/8-inch

(9.5mm) from the center of the horn. Use side cutters

to remove any unused arm from the horn so they

don’t interfere with the operation of the servo.



8. Use a #1 Phillips screwdriver to remove the

stock servo horn from the servo. Install the servo

horn prepared in Step 6 on the servo. Note the

position of the servo horn for the rudder and

elevator servos.



9. Insert the rudder servo in the fuselage by placing

the servo in the servo tray at an angle, then rotating

it into position. Note that the output shaft on the

servo faces to the front of the fuselage.



10. Slide the rudder servo into position. The

rudder pushrod will align with the hole in the

servo horn enlarged in Step 6. Use a pencil to

mark the location for the servo mounting screws

on the servo tray.



11. Remove the servo from the servo tray. Use a pin

vise and 1/16-inch (1.5mm) drill bit to drill the four

holes for the servo mounting screws.

«
...
17
18
19
20
21
...
»

Содержание Aeronca Champ 15E ARF





































Отзывы:

Нет отзывов

Похожие инструкции для Aeronca Champ 15E ARF

Бренд: Bell Страницы: 220

Бренд: Old School Model Works Страницы: 18

P-40 "Curtiss KittyHawk"

Бренд: Vinh Quang Страницы: 11

F/A-18E interior S.A.

Бренд: Eduard Страницы: 4

Бренд: GREAT PLANES Страницы: 35

Бренд: Little Tikes Страницы: 28

Бренд: GRAUPNER Страницы: 42

Бренд: Uberstix Страницы: 40

Lights & Sounds

Бренд: Learning Resources Страницы: 2

VISION Line 700E Hudson

Бренд: Lionel Страницы: 32

3D Puzzle Chrysler Building Night Edition

Бренд: Ravensburger Страницы: 4

Бренд: Faller Страницы: 8

Lionel Quantum-1 System

Бренд: QSI Страницы: 26

Havoc Turbo Blast

Бренд: Air Hogs Страницы: 4

Chocolate Sprinkle Stix

Бренд: John Adams Страницы: 2

Albatross D.III

Бренд: Dancing Wings Hobby Страницы: 4

Impulse Laser Gun Rifle Set

Бренд: Jamara Страницы: 8

Бренд: Faller Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды