E.F. Johnson Company 5300 Series Скачать руководство пользователя страница 52

Страница: 52 / 73

MISCELLANEOUS

7.2 ERROR MESSAGES

The following are definitions of the various error

messages that may be displayed.

Aff Failed -

A group affiliation attempt has received a

FAILED response from the system. The precise reason
for a FAILED response is manufacturer dependent.

Aff Deny -

A group affiliation attempt has received a

DENIED response from the system. The precise
reason for a DENIED response is manufacturer depen-
dent. One common cause is that the group is
disallowed on the site/RFSS that the radio is
attempting to affiliate on.

Aff Refusd -

A group affiliation attempt has received

a REFUSED response from the system. The precise
reason for a REFUSED response is manufacturer
dependent.

Answr Only -

The user has attempted to initiate a

private call or interconnect call and the feature is
programmed for answer only.

Bad Band -

A profile/or user parameters have been

downloaded with PCConfigure that are for a band
different from the hardware of the radio.

Bad ESN -

The ESN of the radio is not valid. This

error is usually only seen in the factory when first
programming brand new logic boards.

Bad Fl Fmt -

A profile/or user parameters have been

downloaded to the radio that do not match the file
format supported by the firmware/software in the
radio.

Bad Hrdwar -

The ESN of the radio is not valid. This

error is usually only seen in the factory when first
programming brand new logic boards.

Batt Low -

The battery voltage has been detected as

being low.

Busy -

A call has been attempted and the system has

responded that no channels are available for assign-
ment.

Busy Tmout -

The radio previously received a busy

response from the system and it has not received a

channel grant before the busy time-out timer has
expired

Disabled -

The selected channel is disabled.

Clear Only -

The selected channel or group is

strapped clear only and that a secure call can not be
made.

Corupt Prm -

The radio has detected that its profile/

user parameters are not valid because the functional
blocks can not be identified.

Denied -

A group call attempt has received a DENIED

response from the system.

Deny -

A unit or interconnect call attempt has received

a DENIED response from the system.

Disabled -

The feature that the user is attempting to

use has been disabled on the radio either by program-
ming or by factory options.

DSP Failed -

The main processor and the DSP have

failed to complete their startup procedure at powerup.

EEPRM Fail -

The main processor has timed out

while trying to validate or invalidate the profile/user
parameters in the EEPROM.

Encryp Bad -

The main processor and the Encryption

Module have failed to complete their startup procedure
at power up.

Fixed High -

The selected channel or group is

strapped to high power and thus low power can not be
selected.

Fixed Low -

The selected channel or group is strapped

to low power and thus high power can not be selected.

Too Hot -

The mobile has passed the hot temperature

threshold. Under these conditions the radio will only
transmit in low power.

Invalid -

The received input from the user does not fit

the criteria necessary for the feature.

Invalid ID -

The received ID from the user was not a

valid ID.

Содержание 5300 Series










































































Результаты поиска

Содержание 5300 Series

Отзывы:

Похожие инструкции для 5300 Series

Бренды по названию

Популярные бренды

E.F. Johnson Company 5300 Series, Руководство по эксплуатации

Результаты поиска

Содержание 5300 Series

Отзывы:

Похожие инструкции для 5300 Series

Бренды по названию

Популярные бренды