background image

 

Maximum Power 

75W 

Speed Stage 

Pump Water Outlet 
Connection 

G3/4 (External Thead) 

Manometer Connection 

Closed 

Drain Valve 

Integrated pump 

 

Water Pressure Sensor 

The water pressure sensor prevents the device from operating at low water pressure. When the water 
pressure at the central heating circuit falls below 0.4 bar, the normally open water pressure sensor 
closes and blocks the operation of the mainboard combination with the signal from the water pressure 
sensor. When the water pressure rises above 0.8 bar, the boiler returns to normal operation. The water 
pressure  sensor  is  located  on  the  flow  manifold  (in  the  central  heating  flow  line).  Sensors  are 
assembling with clips. Option 1 and 2 are using same water pressure sensor.  
 

 

 

Plate Heat Exchanger 

The  plate  exchanger  is  a  second  exchanger  that  provides  heating  of  the  domestic  hot  water  in 
monothermic  models.  When  hot  water  is  needed,  the  3-way  motorized  valve  directs  the  central 
heating water from the main exchanger to the plate heat exchanger. The plate heat exchanger allows 
heat to be transferred to the domestic hot water as it passes through the central heating water. For 
24 kW combi boiler, 10 plate plate heat exchanger is used. The plate exchanger is mounted on the 
hydroblock with 2 imbus bolts. O-ring sealing is provided at the inlet and outlet of domestic hot water 
and central heating water. 
 

Turbine (Water Flow Sensor) 

Turbine measures domestic hot water flow. In both bitermic and monothermic models, it is integrated 
in the hydroblock (return manifold). When the water is flowing, the turbine turns and forms a magnetic 
field. The Hall effect sensor collects the generated magnetic field and informs the electronic card. The 
electronic card controls the operation of the hot water according to the frequency values from the 
turbine type. When the water flow frequency reaches 3 lt/min, the hot water enters the operating 
circuit and when it falls below 2,5 lt / min the hot water operation ends. 
 

Содержание GP11























Отзывы: