Dynisco UPR800 Series Скачать руководство пользователя страница 74

Страница: 74 / 78

DYNISCO UPR800 Series Instruction Manual

Page | 74

Lower display:

LI.TYP

Range:

OFF, AL, P, AL-P. Disabled, alarm reset, peak reset, alarm and peak
reset

Default value:

Alarm and peak reset

LOGIC INPUT STATUS - Group 4

Available:

Only if LI.TYP is different than OFF.

Upper display:

Status of logic input.

Lower display:

LI.STS

Range:

CLOSE, OPEn. The logic input is considered active when the contact
is closed or open with respect to this parameter.

Default value:

Closed.

PEAK DETECTION - Group 4

Available:

Always.

Upper display:

Polarity of peak detector

Lower display:

PEAK

Range:

OFF, HI, LO. Disabled, maximum peak, minimum peak

Default value:

Maximum peak

PRESSURE INPUT DISPLAY UPDATE TIME - Group 4

Available: Always.
Upper display:

Display update time for the pressure input.

Lower display:

PI.DUT

Range: 0.050,

0.100,

0.250,

0.400

sec.

Default value:

0.400 sec.

SECONDARY INPUT SAMPLE TIME - Group 4

Available:

Only if SI.FNC is equal to ‘tenp’.

Upper display:

Sample time for the secondary input.

Lower display:

SI.ST

Range: 0.100,

0.200,

0.500,

1.000

sec.

Default value:

0.500 sec.

LINE FREQUENCY - Group 4

Available: Always.
Upper display:

Line frequency rejection.

Lower display:

LINE.F

Range: 50,

60,

Auto

50 Hz, 60 Hz, automatic detection of the line frequency (except
24Vdc power supply).

Default value:

Auto.

LINE FREQUENCY READOUT - Group 4

Available:

Only when the LINE.F parameter is set to Auto.

Upper display:

Read-only value of the detected line frequency.

Lower display:

LINE.R

Содержание UPR800 Series















































































Результаты поиска

Содержание UPR800 Series

Отзывы:

Похожие инструкции для UPR800 Series

Бренды по названию

Популярные бренды

Dynisco UPR800 Series, Инструкция по эксплуатации

Результаты поиска

Содержание UPR800 Series

Отзывы:

Похожие инструкции для UPR800 Series

Бренды по названию

Популярные бренды