manualshive.com logo in svg

Dynatup 8250, Руководство по эксплуатации

Поделиться
Скачать
Dynatup 8250 Скачать руководство пользователя страница 4

Preliminary Pages

M14-13655-EN

iv

Warning

Disconnect the electrical power supply before removing the covers to
electrical equipment.

Disconnect equipment from the electrical power supply before removing any electrical
safety covers or replacing fuses. Do not reconnect the power source while the covers are
removed. Refit covers as soon as possible.

Disconnect power supplies before removing the covers to rotating
machinery.

Disconnect equipment from all power supplies before removing any cover that gives
access to rotating machinery. Do not reconnect any power supply while the covers are
removed unless you are specifically instructed to do so in the manual. If the equipment
needs to be operated to perform maintenance tasks with the covers removed, ensure that
all loose clothing, long hair, etc. is tied back. Refit covers as soon as possible.

Shut off the supply of compressed gas and discharge residual gas
pressure before you disconnect any compressed gas coupling.

Do not release gas connections without first disconnecting the gas supply and discharging
any residual pressure to zero.

Use protective shields or screens if any possibility exists of a hazard
from the failure of a specimen, assembly or structure under test.

Use protective shields whenever a risk of injury to operators and observers exists from
the failure of a test specimen, assembly or structure, particularly where explosive
disintegration may occur. Due to the wide range of specimen materials, assemblies or
structures that may be tested, any hazard resulting from the failure of a test specimen,
assembly or structure is entirely the responsibility of the owner and the user of the
equipment.

Protect electrical cables from damage and inadvertent disconnection.

Protect all electrical cables, particularly transducer cables, from damage. Never route
cables across the floor without protection, nor suspend cables overhead under excessive
strain. Use padding to avoid chafing where cables are routed around corners or through
wall openings.

Wear protective clothing when handling equipment at extremes of
temperature.

Materials testing is often carried out at non-ambient temperatures using ovens, furnaces
or cryogenic chambers. Extreme temperature means an operating temperature exceeding
60 °C (140 °F) or below 0 °C (32 °F). You must use protective clothing, such as gloves,
when handling equipment at these temperatures. Display a warning notice concerning
low or high temperature operation whenever temperature control equipment is in use.
You should note that the hazard from extreme temperature can extend beyond the
immediate area of the test.

Содержание 8250

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды