Dynapac DFP12D Скачать руководство пользователя

Страница: 85 / 98

8.7.7 Changing the oil in the exciter housing

NOTICE!
Components may get damaged!

–

Use only oil of the permitted specification

Chapter 8.3 „List of fuels and lubri-

cants“ on page 69

Protective equipment:

Working clothes

Protective gloves

Park the machine on level ground.

Park the machine in secured condition

Chapter 6.5

„Parking the machine in secured condition“ on page 58

Tilt the machine slightly towards the oil drain side and sup-

port it safely.

Unscrew the oil drain plug (1) and collect running out oil.

Stand the machine upright.

NOTICE!
Components may get damaged!

Do not use low-ash engine oils for the exciter shaft

housing.

Fill in fresh oil up to the bottom edge of the opening.

Screw in the oil drain plug (1).

Dispose of oil in an environmentally friendly way.

8.7.8 Cleaning the exhaust screen

Protective equipment:

Working clothes

Protective gloves

Park the machine in secured condition

Chapter 6.5

„Parking the machine in secured condition“ on page 58

Allow the engine to cool down.

Fig. 84

Fig. 85

Maintenance – Annually

DFP12D

Содержание DFP12D



































































































Результаты поиска

Содержание DFP12D

Отзывы:

Похожие инструкции для DFP12D

Бренды по названию

Популярные бренды

Dynapac DFP12D, Руководство по эксплуатации

Результаты поиска

Содержание DFP12D

Отзывы:

Похожие инструкции для DFP12D

Бренды по названию

Популярные бренды