Dynapac CA3500DCP, Инструкция по эксплуатации, Страница: 17 / 178

Safety - General instructions
4812165301.pdf 2022-09-02
Safety - General instructions
(Also read the safety manual)
• The operator must be familiar with the contents of the OPERATION section
before starting the roller. • The operator must be familiar with the contents of the OPERATION section
before starting the roller.
• Ensure that all instructions in the MAINTENANCE section are followed. • Ensure that all instructions in the MAINTENANCE section are followed.
• Only the operator is allowed to be on the roller. Remain seated at all times
when operating the roller. • Only the operator is allowed to be on the roller. Remain seated at all times
when operating the roller.
•
Never use the roller if it is in need of adjustment or repair.
•
Never use the roller if it is in need of adjustment or repair.
•
Only ascend and descend the roller when it is stationary. Use the intended
footsteps, grips and rails. Always use the three-point grip (both feet and one
hand, or one foot and both hands) when ascending or descending the
machine. Never jump down from the machine.
•
Only ascend and descend the roller when it is stationary. Use the intended
footsteps, grips and rails. Always use the three-point grip (both feet and one
hand, or one foot and both hands) when ascending or descending the
machine. Never jump down from the machine.
• Dynapac always recommends mounted ROPS (Roll Over Protective
Structure), or a ROPS-approved cab and seat belt usage. • Dynapac always recommends mounted ROPS (Roll Over Protective
Structure), or a ROPS-approved cab and seat belt usage.
•
Drive slowly in sharp bends.
•
Drive slowly in sharp bends.
•
Avoid driving across slopes. Drive straight up or straight down the slope.
•
Avoid driving across slopes. Drive straight up or straight down the slope.
•
Never operate with the drum outside the edge, the substrate might not have
full bearing strength or the edge is close to a slope. Avoid operating close to
edges and ditches and the like as well as on poor ground conditions that
jeopardizes the bearing strength and capacity to support the roller.
•
Never operate with the drum outside the edge, the substrate might not have
full bearing strength or the edge is close to a slope. Avoid operating close to
edges and ditches and the like as well as on poor ground conditions that
jeopardizes the bearing strength and capacity to support the roller.
• Make sure that there are no obstacles in the direction of travel, on the
ground, in front of or behind the roller, or overhead. • Make sure that there are no obstacles in the direction of travel, on the
ground, in front of or behind the roller, or overhead.
•
Drive particularly carefully on uneven ground.
•
Drive particularly carefully on uneven ground.
•
Keep the roller clean. Clean any dirt or grease that accumulates on the
footsteps or operator platform to avoid slipping risk. Keep all signs and
decals clean and legible.
•
Keep the roller clean. Clean any dirt or grease that accumulates on the
footsteps or operator platform to avoid slipping risk. Keep all signs and
decals clean and legible.
•
Safety measures before refueling:
- Stop the engine
- Do not smoke.
- No naked flames in the vicinity of the roller.
- Earth the filling equipment nozzle by keeping it in contact to the tank
opening to avoid sparks.
•
Safety measures before refueling:
- Stop the engine
- Do not smoke.
- No naked flames in the vicinity of the roller.
- Earth the filling equipment nozzle by keeping it in contact to the tank
opening to avoid sparks.
• Before repairs or service:
- Chock the drums/wheels.
- Lock the articulation if necessary.
- Place blocks under overhanging equipment, such as strike-off blade, edge
cutter/compactor and chip spreader. • Before repairs or service:
- Chock the drums/wheels.
- Lock the articulation if necessary.
- Place blocks under overhanging equipment, such as strike-off blade, edge
cutter/compactor and chip spreader.
5