Dyadic Systems SCL Series Скачать руководство пользователя страница 7

Страница: 7 / 63

. .

Dyadic Systems – Mechatronics Cylinder Manual

-005500-EN-7/63

(8) Emergency Stop: During the movement of Mechatronics Cylinder, the movement will stop if the

Interlock signal is interrupted.

(9) Programmable Zone Signal Output: Mechatronics Cylinders can be programmed to output a Zone

Signal.

(10) An air compressor is not needed so that systems using Mechatronics Cylinders will have high energy

efficiency.

(11) Oil waste is not generated so that oil collection equipment is not needed.

(12) Dampers (Shock absorbers) are not needed.

Emergency
Stop Signal

OFF

Zone Signal Output

Zone Signal Output Area

Stop
condition

Speed

Time

Acceleration

Deceleration

Acceleration

Stop
condition

Speed

Time

Acceleration

Deceleration

Содержание SCL Series
































































Результаты поиска

Содержание SCL Series

Отзывы:

Похожие инструкции для SCL Series

Бренды по названию

Популярные бренды

Dyadic Systems SCL Series, Руководство по эксплуатации

Результаты поиска

Содержание SCL Series

Отзывы:

Похожие инструкции для SCL Series

Бренды по названию

Популярные бренды