DWT 742548, Оригинальное руководство пользователя, Страница: 19 / 156

19
English
• To dismount, remove the slot of dust bag 9 from dust
removal port 4 (see fig. 2.2).
Emptying the dust bag (see fig. 2)
[ESS02-187 T]
One should monitor dust level in dust
bag 9 and empty the bag at relevant time,
taking the aforesaid precautions.
• Disconnect the power tool and remove dust bag 9 in
the manner described above�
• Remove textile bag 10 from the plastic body 11 (see
fig. 2.3).
• Taking the precautions described above, empty
the content of textile bag 10 by shaking, for better
results, turn the bag inside out and use a soft brush
to clean it (see fig. 2.4-2.6). When washing textile
dust bag 10, use it only after the bag has dried
completely.
• Put textile dust bag 10 on plastic body 11 (see
fig. 2.7).
Mounting / dismounting of the dust-collecting con-
tainer (see fig. 3)
[ESS03-230 DV]
• During assembly put the dust-collecting container 7
onto a dust removing port 4 (see fig. 3.1).
• During disassembly take the dust-collecting con-
tainer 7 off from the dust removing port 4 (see fig. 3.2).
Emptying the dust-collecting container (see fig. 3)
[ESS03-230 DV]
Monitor the dust-collecting container 7
filling, and empty it promptly according
to safety precautions described above.
• Turn off the power tool and take off the dust-collect-
ing container 7 as described above�
• Press on two holding locks on the cover 12 and take
the cover 12 off (see fig. 3.3).
• Observing safety regulations, dump the container
body 13 contents out; for better results, clean the in-
ner surfaces of the body 13 and cover 12 with a soft
brush (see fig. 3.4-3.6). Attention: in case of clean-
ing dust-collecting container 7 with water, use it
only after complete drying.
• Install the cover 12 on its place - both cover plastic
holding locks 12 should click�
Initial operating
of the power tool
Always use the correct supply voltage: the power sup-
ply voltage must match the information quoted on the
power tool identification plate.
Switching the power
tool on / off
Switching on:
Move switch 3 to the right (see fig. 4.1).
Switching off:
Move switch 3 to the left (see fig. 4.2).
Dust suction during
the power tool operation
Dust collection decreases dust concentra-
tion in the air and prevents build up of dust at
the work station�
Use of vacuum cleaner
During prolonged wood machining or when process-
ing materials that produce dusts hazardous to health,
the power tool should be connected to a proper vac-
uum cleaner�
Given power tools may cooperate with the vacuum
cleaner only when used with a relevant connec-
tor�
One should monitor dust level in the bag and empty
the bag at relevant time, taking the aforesaid precau-
tions�
Design features
of the power tool
Oscillation rate regulator
[ESS03-230 DV]
The oscillation rate regulator 1 is purported to set the
desired oscillation rate of sanding plate 5 �
The required oscillation rate depends on the type of
processed material, work conditions and must be set
on the basis of practical trials for best results�
During prolonged work at low oscillation rate, one
should allow the power tool to cool down for 3 minutes�
For this purpose, set the maximum oscillation rate and
allow the power tool to work without load�
Recommendations
on the power tool operation
Sanding sheet selection
• Prior to commencement of work, select the sanding
sheet type that is most suitable for the processed ma-
terial or surface. The type of sanding sheet is specified
on the package� One may also ask the vendor for more
information�
• Various works require the use of sanding sheet of
different coarseness, allowing a surface of required
smoothness to be obtained:
• in order to flog timber or unplanned boards, re -
move paint or rust, it's recommended to use abra-
sive paper with 40-60 grain size;
• in order to remove minor roughness on surface
of wooden blanks, polish prime coating etc�, it's rec-
ommended to use abrasive paper with 80-120 grain
size;
• for fine polishing of wooden blank surfaces,
grinding of hardwood of prime coatings before
painting, it's recommended to use abrasive paper
with 180-320 grain size�
• The data above are a recommendation only, the
best method to select the grain size for the treated ma-
terial is practical testing�