Dutec I/O Plexer Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 64

Dutec I/O Plexer Скачать руководство пользователя страница 41

Setup 3

3 - 5

The unit is now in the operational mode and the sequential display cycle
becomes*:

U0=00

U1=40

U2=80

U3=C0

U4=d0

U5=E0

H012

L3

P2

Address Setup via network- VARIABLE mode only

Each function address, including the master control address, of the I/O PLEXER
can be set individually by using a special instruction to the current master control
address of that chassis. This “set variable address” instruction should be used
with caution as it will change the unit address and save them in the EEPROM
(see appendix C, C). Consult the I/O PLEXER protocol manual for details.

In the event that the new addresses become lost, they will appear on the
sequential display.

The pushbutton method can always be used to return to the OFFSET mode.

Hardware Error Codes:

When the I/O PLEXER is initially turned on, it goes through internal self test. If
anything is not correct, the appropriate error code will flash on the sequential
display. Try recycling power, if that does not resolve the error condition please
call duTec Technical support at (800)- 248-1632.

* Factory default values for an IOP-AD/3+ depicted in this example

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
39
40
41
42
43
...
»

Содержание I/O Plexer

































































Отзывы:

Нет отзывов