Dutec I/O Plexer Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 64

Dutec I/O Plexer Скачать руководство пользователя страница 18

Installation 2

2 - 2

Figure 2-2 Power wiring

The center terminal block position, adjacent to the letter G on the end of the I/O
module board, is chassis/ earth ground which is connected to the I/O PLEXER
case.

Standard 85-132 VAC, 47-440 Hz and option /E5 105-265 VAC 47-440Hz
Operation.
Following power wiring conventions(AWG)

Black wire to terminal marked H (hot)
White wire to the terminal marked N (neutral)
Green wire to the terminal marked G (chassis/ earth ground)

Option /B or /C 10-30 VDC Operation

+ of the power source to the terminal marked H
- of the power source to the terminal marked N
Earth Ground, where available to the terminal marked G

Digital Expander

The I/O PLEXER Digital Expander (IOP-DE) Receives its power and signals
from the I/O PLEXER via the included 24 pin keyed ribbon cable (duTec part
#CE-24) No other power wiring is required. See page 2-14

I/O Plexer Power supply

terminal block

AC Wiring

DC Wiring

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
16
17
18
19
20
...
»

Содержание I/O Plexer

































































Отзывы:

Нет отзывов