Dutec I/O Plexer Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 64

Dutec I/O Plexer Скачать руководство пользователя страница 25

Installation 2

2 - 9

Modem to I/O Plexer - RS-232

Figure 2-10 link via modem

Two handshake control lines are provided on the I/O PLEXER for interfacing to
modems. They are request to send (RTS) and Clear to send (CTS). An active
high RTS signal from the I/O PLEXER advises the modem that data is available.
When the modem is ready to accept data, it places its CTS line active high to the
I/O PLEXER thus initiating the data exchange.

In addition to the modem to I/O PLEXER wiring the installer should confirm that
JP3 (RTS/CTS Jumper) is positioned as shown in figure 2-10. Jumper JP5
(RTS/CTS for the local RS-232 port), should remain in the horizontal position
unless the RTS/CTS pair is needed in the device connected to the local RS-232
port. A cable for most modem applications, the IOP-RT cable, is available from
duTec.

The switches marked “Pull up” in figure 2-5 should be left in the “on” position.

Note:

If the modem must make use of the RTS/CTS hardware
handshake, only one I/O PLEXER can be used per modem.
If more than one I/O PLEXER is used at a given remote site,
care should be taken that the modem does not need the
RTS/CTS handshaking or external hardware will be
required.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
23
24
25
26
27
...
»

Содержание I/O Plexer

































































Отзывы:

Нет отзывов