DUROMAX XP18HPX Скачать руководство пользователя страница 36

Страница: 36 / 70

MAINTENANCE AND CARE (CONTINUED)

Checking the Oil

Check the oil

The engine is equipped with an automatic shutoff to protect

it from damage due to low oil. Nonetheless, you should check

the oil level of the engine before each use to ensure that the

engine crankcase has a sufficient amount.

To check the oil level:

Make sure the engine is on a level surface.

Unscrew the oil filler/dipstick cap.

With a dry cloth, wipe the oil off of the stick on the

inside of the cap.

Insert the dipstick as if you were replacing the

cap and then remove it again. There should now be

oil on the stick. If there is no oil on the stick, or oil

only at the very end of the stick, you should add

oil until the engine crankcase is filled (see “Adding

Oil” portion of the “Maintenance” section).

The oil will be visible in the oil fill spout when full.

Be sure to replace the cap when finished checking

oil.

Model Number

XP18HPX

Engine Oil Capacity

37.2 fl. oz (1.1 L)

Содержание XP18HPX







































































Результаты поиска

Содержание XP18HPX

Отзывы:

Похожие инструкции для XP18HPX

Бренды по названию

Популярные бренды

DUROMAX XP18HPX, Руководство пользователя

Результаты поиска

Содержание XP18HPX

Отзывы:

Похожие инструкции для XP18HPX

Бренды по названию

Популярные бренды