DUROMAX XP18HPX Скачать руководство пользователя страница 17

Страница: 17 / 70

Add oil

The engine requires engine oil to operate properly. The engine, when new from the package
contains no oil in the crankcase

. You must add the proper amount of oil before operating the

engine for the first time. This amount is equal to the oil capacity of the engine crankcase:

Make sure the engine is on a level surface.

Unscrew the oil filler cap from the engine .

Using a funnel, add the appropriate amount of oil

into the crankcase. You can check the oil level of the

engine with the dipstick located below the oil

filler cap. Simply pull the dipstick out and the

indicated oil level is on the end of the stick.

Replace oil filler cap.

Step 1- Adding Oil

Model Number

XP18HPX

Engine Oil Capacity

37.2 fl. oz (1.1L)

WARNING

: DO NOT overfill the crankcase. This

may damage the motor and shorting overall life

of your engine.

WARNING

Do not apply engine oils with additives or 2-stroke gasoline engine oils;

they don’t have enough lubrication and may shorten the engine’s service life.

Engine oil recommended: SAE 10W-30.

Viscosity varies with regions and temperatures. Choose your

oil viscosity using the chart to the left.

* A small amount of oil from factory testing may be present on

arrival.

* Synthetic oil may be used after the 8 hour initial break-in

period. Using synthetic oil does not increase the recommended

oil change interval. Full synthetic 5W-30 oil will aid in starting in

cold temperatures <5ºC (41ºF).

ENGINE SETUP

Содержание XP18HPX







































































Результаты поиска

Содержание XP18HPX

Отзывы:

Похожие инструкции для XP18HPX

Бренды по названию

Популярные бренды

DUROMAX XP18HPX, Руководство пользователя

Результаты поиска

Содержание XP18HPX

Отзывы:

Похожие инструкции для XP18HPX

Бренды по названию

Популярные бренды