background image

11

 

MK2 ROOF

 

Note:

 

Condensation can form on the under side of shed roof. If building paper is required, fit now. Building paper will 

need to be supported by netting or roofing twine.

 

Step 1:

 

Check that the diagonal measurements of the shed are the same. If building on unlevel ground it may be neces-

sary to temporarily brace the shed with pieces of timber from the packaging.

 

Step 3:

 

Starting from the left hand end, centralize Roof 
on  Ridge  Beam.  Ensure  Roof  is  tight  against 
end  Wall  Sheets,  predrill  then  nail  one  50mm 
Clout  through  Rib  into  the  Ridge  Beam.  At  the 
back,  line  up  Ribs  on  the  Roof  Sheet  with  the 
Ribs  on  Wall  Sheet.  Using  one  50mm    Clout, 
nail through Rib into Back Top Plate. Repeat at 
the front.

 

Note The 6 x 50mm Clouts on end ribs are covered by 

the Barge Flashings.

 

 

Step 2:

 

Position  first  Roof  Sheet  centrally  over  Ridge 
Beam  on  the  right  hand  end  of  shed  with  the 
LIP  on  the  left  hand  side.  (For  sheds  with  a 
Clear Roof Panel, go to the next page). Position 
the next Roof Sheet. Ensure it overlaps correct-
ly  then  rivet  together,  400mm  down  from  the 
centre  on  both  sides.  Fit  remaining  Roof 
Sheets.

 

Step 4:

 

Centralize  Roof  at  the  other  end  and  nail 
through  Rib  into  the  Ridge  Beam  and  Top 
Plates,  using  50mm  Clouts.  Ensure  Ridge 
Beam  is  straight,  then  Screw  one  50mm  Roof-
ing  Screw  into  Ridge  Beam  through  each  Rib 
on overlap (one screw per sheet). At the back, 
set up a String Line in centre of Top Plate. En-
sure Top Plate is straight and screw, using one 
50mm  Roofing  Screw  per  Rib.  Repeat  at  the 
front.

 

LIP

 

50mm Clout 

 

Roofing screws

 

Содержание SHEDS MK2

















Отзывы: