background image

OPERATING INSTRUCTIONS

DURAMAX Jr. HT, DURAMAX Jr. T RC, DURAMAX,  DURAMAX BiTURBO T RC

 

 Jr. HT

 

program

 

operates by 

FEATURES

If the machine for any reason gets stuck on the pool floor for more than 
2 minutes or if the machine does not see a wall within 2 minutes it 
reverses itself.. 

OPERATION

After the Power Supply main switch is turned on (fig. a) and the C-
run/Reset Switch is pressed on the power supply,(fig.b) the machine 
will run a test sequence for the first 9 seconds. Then the machine will search for a wall. When it finds a wall the machine will 

climb the wall for 15 seconds, will reverse, go down the wall and move away from the wall for 21 seconds, it will reverse and go 
back towards the wall for 5 seconds. The pump will turn off and  perform a turn. After this the pump will turn back on and will 

return again towards the wall. The machine will climb the wall for 2 seconds, reverse for 25 seconds and will reverse again. 

The machine will repeat this three times. On the fourth time the Cleaner will cross the pool to the opposite wall and repeat the 

first three actions moving in the opposite direction

DURAMAX FEATURES

If for any reason the machine gets stuck on the pool floor for more than 2 minutes or if the machine does not see a wall within 
2 minutes, it reverses itself.  If  for any reason the machine gets out of the water, it will reverse itself every 25 seconds. 
If the machine is on the pool wall and does get down to the pool floor, the machine will reverse itself after 30 seconds and 
then will  reverse again after 30 seconds. If the machine remains on the wall or is up-side down for over 2 ½ minutes, the 
pump will turn off for 30 seconds and let the machine settle to the bottom of the pool. If during the next 30 seconds, the 
machine remains on the wall or up-side down the machine will shut down to protect the cleaner from harm.

The 

DuraMAX

during its 

operation. During this period the Cleaner will turn and then 

continue its cleaning cycle.  

The 

DuraMAX

  c

shutting 

down the Pump Motor for a 6 second period 

cleaning pattern of the 

an be adjusted by the user by adjusting the foam float located on 

the floating handle.  The further from center the float 
is located the further the cleaner will turn.  

Alternatively, the closer the float is towards the center a smaller 
angle can be achieved.  To make the cleaner turn right the float 
should be located on the left side.  To make the cleaner turn left 
locate the float on the right side. Rotating the float from side to side will 
keep the Cable from tangling

7

DuraMAX

Jr.HT

a.

b.

DuraMAX

DuraMax 

DuraMax 

DuraMAX

Jr. T RC

DuraMAX 

BiTurboT  R

  C

Содержание BiTurbo T2

































Отзывы: