Duplo DF-920 Скачать руководство пользователя страница 11

Страница: 11 / 64

4. INSTALLATION

Open the top cover, rotate the jam correction
knob to check that folding plate 1 is properly
secured. If the knob rotates smoothly, it means
that folding plate 1 is secured.

Jam correction knob

Top cover

Connect control cord 1 of folding plate 1 to the
No.1 connector.

Be sure to turn off the power before
connecting or disconnecting the control
cord. Otherwise the unit will malfunction.

Note

No.1 connector

Control cord 1

Attach folding plate 2.

Open the side cover.

Side cover

Set guide

Push the lock lever on folding plate 2 towards
“UNLOCK”.

UNLOCK

LOCK

Push in folding plate 2 along the set guide to the
“2 (

)” mark. The safety stopper locks at this

position.

Folding plate 2

Be sure to insert the folding plate holding
the handle with both hands.

Note

While slightly lifting folding plate 2 with the
handle, push in it to the “1 ( )” mark.

Folding plate 2

Содержание DF-920

































































Результаты поиска

Содержание DF-920

Отзывы:

Похожие инструкции для DF-920

Бренды по названию

Популярные бренды

Duplo DF-920, Инструкция по эксплуатации

Результаты поиска

Содержание DF-920

Отзывы:

Похожие инструкции для DF-920

Бренды по названию

Популярные бренды