manualshive.com logo in svg
background image

VDP1500SSM

 

VELLEMAN 

VDP1500SSM - PROFESSIONAL DMX-CONTROLLED SMOKE MACHINE 

 

1. Introduction 

 

To all residents of the European Union 

Important environmental information about this product 

 
This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm the environment. 
Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialised company for recycling. 
This device should be returned to your distributor or to a local recycling service. 
Respect the local environmental rules. 

If in doubt, contact your local waste disposal authorities. 

 

Thank you for buying the 

VDP1500SSM

! If the device was damaged in transit, don't use it and contact your dealer. 

 

2. Safety Instructions 

 

Be very careful during the installation: touching live wires can cause life-threatening electroshocks. 
 
Do not touch the device during operation as the housing heats up. 
 
Keep this device away from rain and moisture. 
 
Unplug the mains lead before opening the housing. 

 

 

Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer 

will not accept responsibility for any ensuing defects or problems. 

 

A qualified technician should install and service this device. 

 

Do not switch the device on immediately after it has been exposed to changes in temperature. Protect the device 

against damage by leaving it switched off until it has reached room temperature. 

 

Have a qualified person carry out the electric connection. 

 

Make sure that the available voltage does not exceed the voltage stated in the specifications of this manual. 

 

Do not crimp the power cord and protect it against damage. Have an authorised dealer replace it if necessary. 

 

Disconnect the device from the mains to clean it or when it is not in use. Handle the power cord by the plug only. 

 

Note that damage caused by user modifications to the device is not covered by the warranty. 

 

Keep the device away from children and unauthorised users. 

 

3.  General Guidelines 

 

 

This device is designed for professional use on stage, in discos, theatres, etc. The 

VDP1500SSM

 should only be 

used indoors with an alternating current of max. 230VAC / 50Hz. 

 

This device is not suited for permanent operation. Frequent operation breaks will protect the life span of your 

smoke machine. 

 

Do not shake the device. Avoid brute force when installing or operating the device. 

 

Select a location where the device is protected against extreme temperatures, dust and moisture. 

 

Familiarise yourself with the functions of the device before actually using it. Do not allow operation by unqualified 

people. Any damage that may occur will most probably be due to unprofessional use of the device. 

 

Use the original packaging if the device is to be transported. 

 

All modifications of the device are forbidden for safety reasons. 

 

Only use the device for its intended purpose. All other uses may lead to short circuits, burns, electroshocks, 

crash, etc. Using the device in an unauthorised way will void the warranty. 

 

4. Installation 

 

 

Have the device installed by a qualified person, respecting EN 60598-2-17 and all other applicable norms. 

 

The carrying construction must be able to support 10 times the weight of the device for 1 hour without deforming. 

Содержание HQ Power VDP1500SSM














Отзывы: