Dungs FRM-NOC 100025 HD Скачать руководство пользователя страница 41

Страница: 41 / 76

40 … 76

MC • Edition 2022.08 • No

. 279 663 R

. -0

41 … 76

only with external pulse

5.0 Initial Checking of the FRM outlet pressure

5.1 Before initially starting of the equipment, an initial

check of the FRM outlet pressure setting shall be

done.

5.2 To check the outlet pressure setting of the regulator:

5.3 Partially open a manual valve connected to the hose

in 4.0 above just enough to generate gas flow, and

check the set value (outlet pressure) using a pres

sure gauge. If necessary, correctly adjust the setting

according to section 11.1 Regulator Setting.

5.4 Close the manual valve, remove the hose, insert the

sealing cap A.

6.0 Checking upper(over) response pressure p

6.1 SBV installation on the outlet side: block the line

upstream of the SBV.

6.2 Create bypass around the FRM (see below).

6.3 Connect a line between the inlet and outlet side of

FRM using manually operated test/purge valves.

6.4 With both valves closed, slowly open the upstream

valve to charge the bypass line.

6.5 Slowly open the downstream valve in the bypass line

and monitor the increase of pressure on the outlet

side using a pressure gauge.

6.6 Avoid inadmissible high pressure on the outlet side.

Stop applying pressure immediately after the SAV

has tripped.

6.7 Once the SAV trips, read the upper (over) response

pressure on the pressure gauge on the outlet side.

6.8 If necessary, correct the SAV set points according to

the specifications in section 11.2 "SAV setting" and

check it again.

7.0 Check of the lower (under) response pressure

setting.

7.1 Release the pressure in the test section on the outlet

side until the operating pressure is reached.

7.2 Check if gas is available and release it safely in the

atmosphere.

7.3 Monitor pressure drop on the pressure gauge.

7.4 Unlock / reset SAV, if SAV is tripped.

See "3. SAV resetting" in section 12.4.

7.5 Check that all test/purge valves are closed.

7.6 Create a means to safely release the fuel gas in

downstream the SAV into the atmosphere. See

figures below and reference "4.0 Venting the test

section to atmosphere" in section 12.3.

7.7 Slowly vent the fuel gas per "4.0 Venting the test

section to atmosphere". After the SAV trips, read the

lower (under) response pressure on the pressure

gauge.

7.8 Close the vent valve, remove the hose, insert the

sealing cap.

7.9 Slowly open the shut-off valve on the inlet side.

Connections and Setup for venting the test section

Connections and Setup of a bypass line

Содержание FRM-NOC 100025 HD













































































Результаты поиска

Содержание FRM-NOC 100025 HD

Отзывы:

Dungs FRM-NOC 100025 HD, Инструкция по эксплуатации, Страница: 41 / 76

Результаты поиска

Содержание FRM-NOC 100025 HD

Отзывы: