Dungs 273061 Скачать руководство пользователя страница 5

Страница: 5 / 56

4 …56

MC • Edition 04.19 • No

. 278 349

5 … 56

5. List of abbreviations

Abbreviation Description
AG

Response pressure group of the upper response pressure

Response pressure group of the lower response pressure

Accuracy class

ASE

Safety shutoff valve (without housing)

Flow volume coefficient

Nominal diameter

Fail-open

The firing valve moves automatically to the open position, if the main diaphragm or the

auxiliary power required for the actuation of the firing valve fails

IS/DS

Type: integral strength range (IS) or differential strength (DS)

Class A

Functional class: the SAV closes if the comparison diaphragm is damaged or the auxiliary power supply

has failed

MOP

Maximum admissible operating pressure

Outlet pressure

d, abs.

Output pressure as absolute pressure

Inlet pressure

u, abs.

Inlet pressure as absolute pressure

Upper response pressure

Lower response pressure

max

Maximum operating pressure

zul.

System-specific operating pressure according to the regulator

Nominal pressure of the flange

Maximum admissible pressure

SAV

Safety shutoff valve

SBV

Safety relief valve

Lock-up pressure class

Serial number

Closing pressure zone group

Tp.

Operating temperature -20 °C ... +60 °C

Specific guide range

Adjustment range for the upper response pressure through regulation of the

available adjusting springs

Adjustment range for the lower response pressure through regulation of the

available adjusting springs

dso

Specific adjustment range of the adjusting spring installed for the upper response pressure

dsu

Specific adjustment range of the adjusting spring installed for the lower response pressure

Содержание 273061

























































Результаты поиска

Содержание 273061

Отзывы:

Бренды по названию

Популярные бренды

Dungs 273061, Инструкция по эксплуатации

Результаты поиска

Содержание 273061

Отзывы:

Бренды по названию

Популярные бренды