Dungs 273061 Скачать руководство пользователя страница 24

Страница: 24 / 56

24 …56

MC • Edition 04.19 • No

. 278 349

12. Commissioning and decommissioning

12.2 Leakage test

Prior to commissioning

• The performance data on the type plate correspond to the ordering data.

• Prevent explosive gas-air mixture: the room atmosphere must be monitored through gas con-

centration measuring devices for the detection of gas leakages.

• Only operate the device if all safety devices are fully functional.

• Only qualified personnel are allowed to carry out the commissioning.

12.1 General information

Lekspray

pmax = 10 bar

Before commissioning the device, a test for

internal and external leakages must be carried out.

1. Test gases of the leakage test: air or inert gases.

2. Upstream and downstream shutoff valves must be closed.

3. Release the test section. Check the presence of gas and

safely release to the atmosphere.

4. Test pressure > blow-off pressure SBV: block the line

upstream of the SBV.

5. Connect the test section to the test device and apply pres

sure.

6. Test pressure: 1.1 x system-specific operating pressure

Maximum PS of the device. Different pressure ratings of

the system must be taken into account.

7. Observe the waiting time necessary for the pressure com

pensation according to the system-specific volumes.

External leakage

8. Use a suitable leak detection spray on the device.

9. Monitor the foam formation.

Internal tightness

10. Release the pressure in the test section downstream of

the device.

11. Monitor the increase in pressure on the outlet side: pres

sure gauge accuracy 0.1 mbar

12. Once the leakage test has been carried out, open the

shutoff valve upstream of the SBV.

13. Release pressure in the test section.

Содержание 273061

























































Результаты поиска

Содержание 273061

Отзывы:

Бренды по названию

Популярные бренды

Dungs 273061, Инструкция по эксплуатации

Результаты поиска

Содержание 273061

Отзывы:

Бренды по названию

Популярные бренды