Dungs 273061 Скачать руководство пользователя страница 14

Страница: 14 / 56

14 …56

MC • Edition 04.19 • No

. 278 349

9. Installation
9.1 General information

• This device can only be installed in

compliance with the rules and stand

ards applicable and in accordance with

the local regulations and authorisa -

tions.

• Install the device in a building or

housing, do not install it outdoors without suitable

protective measures!

• The lifting devices used must be suitable for the load

to be lifted.

• Enough installation space for operation and mainte-

nance has to be provided.

• It is recommended to install a filter with a pore size ≤

50 µm upstream of the regulator.

• The installation must not impair the functioning of

other components.

Check prior to installation!

•

Shut-off valves both on the inlet and outlet side are

closed.

•

Lines are free from combustible gas.

•

Prevent explosive gas-air mixture: the room atmosphere

must be monitored for gas leakages.

•

Ensure Ensure electrical continuity with use of suitable

bonding straps. Prevent contact voltage and ignitable

flashover.

•

The performance data on the type plate corresponds to

the purchase ordering data.

•

Flanges on the inlet side and outlet side of the connecting

line are parallel.

•

The sealing surfaces of the flange are undamaged and

clean.

•

The maximum inlet pressure of the system is lower than

the maximum admissible pressure of the regulator.

•

Protective caps at the connection flange, if any, must be

removed.

•

The minimum distances for the setting must be observed.

•

The pipeline on the inlet side must be free of water and

dirt.

Note during installation!

•

Mounting must be carried out in a tension-free state.

•

Tighten the screws crosswise.

•

Tightening torques must be observed.

•

Vent lines and blow-off lines have to be positioned sepa

rately.

•

Vent lines and blow-off lines must lead outdoors: gases

must be able to escape to a non-hazardous environment.

•

The impulse lines may not be shut off.

•

The specified distance between the measuring points of

the impulse lines must be observed.

•

The flow direction (arrow) on the housing must be fol

lowed.

Содержание 273061

























































Результаты поиска

Содержание 273061

Отзывы:

Бренды по названию

Популярные бренды

Dungs 273061, Инструкция по эксплуатации

Результаты поиска

Содержание 273061

Отзывы:

Бренды по названию

Популярные бренды